Cisco TOPSPIN SFS 3012 Hardware Manual Download Page 71

Page: 71 / 79

Controller Card LEDs

Controller cards include card status LEDs as well as Management Ethernet port LEDs. The
top-left-most LED represents the controller card in slot 1, and the top-right-most LED represents the
controller card in port 14.

Figure 5-3

displays the LEDs on the controller card.

Figure 5-3:

Controller Card LEDs

NOTE:

The LEDs immediately below the controller card status LEDs are not currently supported.

Table 5-5

explains Controller Card LED indications.

Table 5-6

explains Management Ethernet port LED indications.

Table 5-5:

Controller Card LED Indications

LED State

Indication

off

No power to the controller card.

solid green

Controller card runs with no errors.

solid yellow

Controller card problem that requires user intervention.

Table 5-6:

Management Ethernet LED Indications

LED State

Indication

Link LED off

No physical link.

Link LED solid

Successful physical link.

Port Activity LED off

No logical link.

Port Activity LED blinking

Traffic runs over the port.

Port Activity LED solid

Logical link established but traffic does not yet run.

Controller Card 1 Status LED

Controller Card 2 Status LED

Management Ethernet Port Link LED

Management Ethernet Port Activity LED

Summary of Contents for TOPSPIN SFS 3012
















































































Search results

Summary of Contents for TOPSPIN SFS 3012

Reviews:

Related manuals for TOPSPIN SFS 3012

Brands by name

Popular brands

Cisco TOPSPIN SFS 3012, Hardware Manual

Search results

Summary of Contents for TOPSPIN SFS 3012

Reviews:

Related manuals for TOPSPIN SFS 3012

Brands by name

Popular brands