manualshive.com logo in svg

Cisco TOPSPIN SFS 3012, Hardware Manual

Share
Download
Cisco TOPSPIN SFS 3012 Hardware Manual Download Page 61

43

•

The keyword 

all

 (The CLI defaults to “all” if you enter just “show card”).

Example

2. Update the switch card firmware. Enter the 

install

 command:

Example

NOTE:

Only cards with an oper-status of “up” are updated. If a card is down when you run install, 

or a card is added after running install, bring up the card and run install again. Specify the same 
image file. If the image is already installed on a card, that card is skipped. Run boot-config again so 
that all cards know to boot off the same system image.

Topspin-360# 

show card 5,9,14,16

============================================================================
                                Card Information
============================================================================
     admin                oper                 admin    oper     oper
slot type                 type                 status   status   code
----------------------------------------------------------------------------
5    en4port1G            en4port1G            up       up       normal
9    fc2port2G            fc2port2G            up       up       normal
14   controller           controller           up       up       normal
16   ib12port4x           ib12port4x           up       up       normal

============================================================================
                             Card Boot Information
============================================================================
     boot         boot               boot
slot stage        status             image
----------------------------------------------------------------------------
5    done         success            TopspinOS-1.1.2/build084
9    done         success            TopspinOS-1.1.2/build084
14   done         success            TopspinOS-1.1.2/build084
16   done         success            TopspinOS-1.1.2/build084

============================================================================
                                  Card Seeprom
============================================================================
     product          pca              pca              fru
slot serial-number    serial-number    number           number
----------------------------------------------------------------------------
5    00024            1234             95-00007-01      1234
9    1234             1234             95-00008-01      1234
14   00002            00002            95-00005-01      1234
16   1234             1234             95-00006-01      1234
Topspin-360#

Topspin-360# 

install image:Topspin-360-TopspinOS-2.0.0-build497.img

************************** operation completed successfully
Topspin-360#

Summary of Contents for TOPSPIN SFS 3012
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands