Cisco TOPSPIN SFS 3012 Hardware Manual Download Page 54

Page: 54 / 79

NOTE:

If you do not have enough available memory to install an additional image, delete an old

image.

“Delete an Image with the CLI” on page 38

3. Specify the new boot image to be used.

Find the name of your new system image by entering the

dir image

command. Copy the name

of the new image.

b. Enter

boot-config primary-image-source

, then paste the copied image file name.

Example

4. Reboot the chassis. Note: You can also use the

card shutdown

and

card no shutdown

commands

or the Element Manager GUI to reboot an individual card if you do not need to update the entire
chassis.

Example

5. Save the system configuration. Click Yes when prompted.
6. Use the

show card-inventory

command to view the new primary image for all cards.

Upgrade the Software Image with the GUI

1. Launch the Element Manager GUI.
2. Select

Maintenance

File Management

. The

File Management

window appears.

Topspin-360#

configure

Topspin-360(config)#

boot-config primary-image-source

TopspinOS-2.1.0/build497

Topspin-360(config)#

exit

Topspin-360#

reload

Summary of Contents for TOPSPIN SFS 3012
















































































Search results

Summary of Contents for TOPSPIN SFS 3012

Reviews:

Related manuals for TOPSPIN SFS 3012

Brands by name

Popular brands

Cisco TOPSPIN SFS 3012, Hardware Manual

Search results

Summary of Contents for TOPSPIN SFS 3012

Reviews:

Related manuals for TOPSPIN SFS 3012

Brands by name

Popular brands