manualshive.com logo in svg

Cisco TOPSPIN SFS 3012, Hardware Manual

Share
Download
Cisco TOPSPIN SFS 3012 Hardware Manual Download Page 4

iv

Introduction..................................................................................................................................................5
Controller Cards...........................................................................................................................................6

Install a Controller Card ................................................................................................................. 6

Ethernet and Fibre Channel Gateways.........................................................................................................9

Replacing and Updating Your Gateways........................................................................................ 9
Install an Ethernet or Fibre Channel Gateway.............................................................................. 10

InfiniBand Switch Cards............................................................................................................................10

Install InfiniBand Switch Cards.................................................................................................... 11
Remove InfiniBand Switch Cards ................................................................................................ 13

Power Supply Modules ..............................................................................................................................13

Install Power Supply Modules...................................................................................................... 14
Removing a Power Supply ........................................................................................................... 15

Blower Trays..............................................................................................................................................15

Install Blower Trays...................................................................................................................... 15
Removing Blower Trays............................................................................................................... 16

5: Install and Boot the Topspin 360..............  19

Introduction................................................................................................................................................19
Prepare the Site for the Topspin 360..........................................................................................................19

Read the Cautionary Statements ................................................................................................... 20
Prepare the Physical Environment for the Topspin 360 ............................................................... 20

Install Topspin 360 Components ...............................................................................................................20
Rack the Topspin 360 ................................................................................................................................20
Attach a Serial Console Cable to a PC or Terminal...................................................................................26
Boot your Topspin 360 and Configure Basic Connectivity.......................................................................27

Assign a Static IP Address............................................................................................................ 27
Obtain an IP Address with DHCP ................................................................................................ 28

Connect InfiniBand Hosts..........................................................................................................................29
Manage the Topspin 360............................................................................................................................32
Viewing and Updating the Software Image on the Chassis.......................................................................33

View the Software Image Version with the CLI .......................................................................... 33
View the Software Image Version with the GUI.......................................................................... 34
Upgrade the Software Image with the CLI................................................................................... 35
Upgrade the Software Image with the GUI .................................................................................. 36
Delete an Image with the CLI....................................................................................................... 38
Delete an Image with the GUI ...................................................................................................... 39

6: Topspin 360 Field Replaceable Units ......  41

Controller Cards.........................................................................................................................................41
Expansion Modules....................................................................................................................................41
InfiniBand Switch Cards............................................................................................................................42

Installing an InfiniBand Switch Card ........................................................................................... 42
Configuring a New InfiniBand Switch Card ................................................................................ 42
Removing an InfiniBand Switch Card.......................................................................................... 44

Power Modules ..........................................................................................................................................44

Summary of Contents for TOPSPIN SFS 3012
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands