Cisco Network Storage System NSS3000 Series Administration Manual Download Page 46

Page: 46 / 184

Configuring your Storage

Storage Status Tables

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

Storage Status Tables

The

Storage Status

page include the following tables:

Disk Status Table

The

Disk Status

table lists each of the physical disks installed in the NSS. The

table is made up of the following columns:

•

Port

: The port number on the NSS in which the disk is installed.

•

Model

: The model of the disk drive. This information is read from the disk

drive.

•

Size

: The size of the disk drive.

•

Health

: The system monitors each disk drive and reports the condition of

the disk drive. Options include:

Passed

: The disk drive has passed the S.M.A.R.T. test and is considered

fully operational. The Error LED on the disk drive is off.

Failing

: The disk drive has failed the S.M.A.R.T. test and is predicated to

fail. The red Error LED on the disk drive is blinking.

Failed

: The disk drive is not operational (has failed). The red Error LED on

the disk drive is on solid.

•

Status

: The state of use for the disk drive. Options include:

Online

: The disk drive is spun up.

Standby

: The disk drive is idle and is spun down.

Offline

: The disk drive is failed.

•

Action

: There are available action buttons associated with each installed

disk drive:

Get Details

: View the current, detailed S.M.A.R.T. report for the

disk drive.

Summary of Contents for Network Storage System NSS3000 Series

























































































































































































Search results

Summary of Contents for Network Storage System NSS3000 Series

Reviews:

Related manuals for Network Storage System NSS3000 Series

Brands by name

Popular brands

Cisco Network Storage System NSS3000 Series, Administration Manual

Search results

Summary of Contents for Network Storage System NSS3000 Series

Reviews:

Related manuals for Network Storage System NSS3000 Series

Brands by name

Popular brands