Cisco Network Storage System NSS3000 Series Administration Manual Download Page 20

Page: 20 / 184

Managing the System

Configuring the System for UPS Support

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

Configuring the System for UPS Support

You can set up the NSS to use an uninterruptible power supply (UPS) if one is
connected directly to the UPS port on the NSS. The

Power

Status

page provides

an overview of the current power condition of the NSS.

NOTE

When the UPS power goes to low battery, a signal is sent through the USB port on
the NSS and a shutdown of the NSS is initiated. Make sure that the UPS has enough
reserve power to sustain the NSS through the shutdown (approximately 5 minutes)

The Power area displays the following:

•

AC Status:

The following options are available depending on the current

operating condition of the UPS. For more information about the functioning
of the UPS, refer to the UPS documentation.

•

Disconnected

: A UPS is not currently connected to the NSS or has not yet

been enabled.

•

Online

: A UPS is connected to the NSS and is enabled. The NSS is deriving

power from the mains power.

•

Battery

: The NSS is currently deriving its power from the UPS battery.

•

Battery

Status

: The percentage of power still available is also listed and is

color-coded according to the amount of battery remaining.

To enable the UPS:

STEP 1

From the

Manager

Menu

, click

System

Power

Summary of Contents for Network Storage System NSS3000 Series

























































































































































































Search results

Summary of Contents for Network Storage System NSS3000 Series

Reviews:

Related manuals for Network Storage System NSS3000 Series

Brands by name

Popular brands

Cisco Network Storage System NSS3000 Series, Administration Manual

Search results

Summary of Contents for Network Storage System NSS3000 Series

Reviews:

Related manuals for Network Storage System NSS3000 Series

Brands by name

Popular brands