manualshive.com logo in svg

Cisco Network Storage System NSS3000 Series, Administration Manual, Page: 27 / 184

Share
Download
Cisco Network Storage System NSS3000 Series Administration Manual Download Page 27

Adding the NSS to your Network

Viewing VLANs Configured on the NSS

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

19

3

STEP 4

Click 

Update

.

Viewing VLANs Configured on the NSS

When you first display the 

Network VLAN

 page, the currently configured VLANs 

appear. Configuring a VLAN to connect to the NSS depends if it is trunk-based or 
port-based. 

•

To configure a trunk-based VLAN, follow the steps to allow a VLAN to 
access the NSS. See 

”Allowing a VLAN Access to the NSS” on page 21

. 

•

To configure a port-based VLAN, configure the switch to assign the port to 
which the NSS is connected to the desired VLAN. In this case, no NSS 
configuration changes are required. 

Summary of Contents for Network Storage System NSS3000 Series

























































































































































































Reviews:

No comments