Cisco FM1000 Gateway Installation And Configuration Manual Download Page 29

Page: 29 / 138

Connecting power through the device power ports

The

DC 12V

connector (1,

) is a two-terminal power

port. The unit is exclusively designed to accept passive 12 Vdc power
from an AC power adapter producing a minimum of 60W (12V/5A).

Figure 9. FM1000 Gateway (DC 12V connector)

CAUTION

Do not connect a 24 Vdc or 48 Vdc power source to the unit
under any circumstances.

4.1.5. Rebooting the firmware and resetting the unit to factory
defaults

The Cisco FM1000 Gateway hardware can be rebooted and reset to
factory default condition using the procedures in this section.

IMPORTANT

The following procedure shows how to do a 'hard' (device
firmware) reboot. To do a 'soft' (device software) reboot, refer
to

“Resetting the unit to factory defaults” (page 105)

To do a 'hard' (device firmware) reboot under emergency conditions (for
example, if the unit malfunctions), do the steps in the following sub-
section.

Device firmware reboot

Connect one end of an RS-232 serial cable to either of the

COM

ports on the rear side of the unit (1 or 2,

Figure 10 (page 30)

Hardware installation

Page 29 of 138

Summary of Contents for FM1000 Gateway








































































































































Search results

Summary of Contents for FM1000 Gateway

Reviews:

Related manuals for FM1000 Gateway

Brands by name

Popular brands

Cisco FM1000 Gateway, Installation And Configuration Manual

Search results

Summary of Contents for FM1000 Gateway

Reviews:

Related manuals for FM1000 Gateway

Brands by name

Popular brands