manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Software Configuration Manual

Share
Download
Cisco ASR1002 - ASR 1002 Router Software Configuration Manual Download Page 395

 

      Configuring MPLS Layer 2 VPNs

  Configuring Gigabit EtherChannel for Virtual Private Wire Service

19

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

Configuring Gigabit EtherChannel for Virtual Private Wire 
Service

The GEC VPWS support feature is supported by AToM on the EtherChannel Interface, and includes the 
following features:

  •

EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking, page 19

  •

EtherChannel-to-EtherChannel over MPLS (Routed) Interworking, page 21

  •

Any-to-EtherChannel over MPLS (Bridged) Interworking, page 24

  •

Any-to-EtherChannel over MPLS (Routed) Interworking, page 26

EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking

Configure L2VPN interworking on the upstream interfaces of the PE routers. For more information 
about configuring L2VPN interworking on the PE routers, see 

L2VPN Interworking Modes, page 2

.

After configuring MPLS Forwarding, perform the following steps on the downstream interfaces of the 
PE routers.

SUMMARY STEPS

1.

enable

2.

configure terminal

3.

mpls label protocol ldp

4.

interface

 

loopback 

loopback-interface-number

5.

ip address 

ip-address ip-subnet-mask

6.

exit

7.

pseudowire-class

 

pw-class-name

8.

encapsulation mpls

9.

interworking ethernet

10.

exit

11.

interface port-channel 

number

12.

xconnect

 

peer-ip-address vc-id

 

encapsulation mpls pseudowire-class

 

pw-class-name

13.

interface GigabitEthernet

 slot | subslot | port

14.

channel-group

 port-channel number

Summary of Contents for ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands