manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Software Configuration Manual

Share
Download
Cisco ASR1002 - ASR 1002 Router Software Configuration Manual Download Page 250

 

      Configuring Cisco License Call Home

  How to Configure Cisco License Call Home

4

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

3.

show license call-home pak

 

pak-id

4.

license call-home install pak 

pak-id

5.

show license feature

DETAILED STEPS

Rehosting a License by Using Cisco License Call Home

Perform this task to rehost (revoke and transfer) a license by using the Cisco License Call Home feature. 
The rehost operation is performed by using a source and a target unique device identifier (UDI).

SUMMARY STEPS

1.

enable

2.

license call-home revoke udi 

target-udi output-of-rehosted-license-url

3.

show license detail

4.

(Optional) 

license install

 

stored-location-url

Command or Action

Purpose

Step 1

Obtain the PAK.

The PAK is provided to you when you order or purchase the 
right to use a feature set for a particular platform. The PAK 
serves as a receipt and is used as part of the process to 
obtain a license.

Step 2

enable

Example:

Router> enable

Enables privileged EXEC mode. 

  •

Enter your password if prompted.

Step 3

show license call-home pak

 

pak-id

Example:

Router# show license call-home pak 3XPXR9E7D30

Displays the stock keeping unit (SKU) list and features 
available for the PAK provided.

Step 4

license call-home install pak 

pak-id

Example:

Router# license call-home install pak 

3XPXR9E7D30

Installs a license by using the Cisco License Call Home 
feature.

  •

Respond to the prompts in the command display.

Step 5

show license feature

Example:

Router# show license feature

Displays the list of licensed features.

Summary of Contents for ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands