Cisco ASR 920-24SZ-IM Installing Download Page 33

Page: 33 / 54

The Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router power supplies are hot-swappable.
If you have installed redundant power supplies, you can replace a single power supply without interrupting
power to the router.

Note

To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after a power supply
has been removed or replaced.

Caution

When you install the unit, the ground connection must always be made first and disconnected last. Statement
1046

Warning

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Follow these steps to remove and replace an AC power supply:

Procedure

Step 1

Disconnect the power cord from the power source. Do not touch the metal prongs on the power cord when it
is still connected to the power supply.

Step 2

Remove the power cord from the power connection on the power supply. Do not touch the metal prongs
embedded in the power supply.

Step 3

Loosen the captive installation screw as shown in the figure below.

Installing the Router

Removing and Replacing an AC Power Supply

Summary of Contents for ASR 920-24SZ-IM























































Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands

Cisco ASR 920-24SZ-IM, Installing

Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands