Cisco ASR 920-24SZ-IM Installing Download Page 27

Page: 27 / 54

Power On the DC Power Supply

After the router is either rack mounted or mounted on the wall, perform these tasks to complete the installation:

Procedure

Step 1

Power on the DC power supply. See the figure below.

Figure 22: Powering on the DC Power Supply

power on/off switch

Step 2

Connect the front-panel ports.

Removing and Replacing a DC Power Supply

This section provides information about removing and replacing a DC power supply in the Cisco ASR
920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router.

The Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router power supplies are hot-swappable.
If you have installed redundant power supplies, you can replace a single power supply without interrupting
power to the router.

Note

To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after a power supply
has been removed or replaced.

Caution

When installing or replacing the unit, the ground connection must always be made first and disconnected last.
Statement 1046

Warning

Installing the Router

Power On the DC Power Supply

Summary of Contents for ASR 920-24SZ-IM























































Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands

Cisco ASR 920-24SZ-IM, Installing

Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands