Cisco ASR 920-24SZ-IM Installing Download Page 29 | Manualshive

Page: 29 / 54

background image

Step 6

Grasping the power supply handle with one hand, pull the power supply out from the chassis while supporting
it with the other hand.

Step 7

Replace the DC power supply within 5 minutes. See

Installing a DC Power Supply

figure. If the power supply

bay is to remain empty, install a blank filler plate (Cisco part number 800-39165-01) over the opening, and
secure it with captive installation screws.

Installing an AC power Supply

The sections describe how to install an AC power supply in the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M,
ASR-920-24TZ-M Router:

This product requires short-circuit (over current) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations. Statement 1045

Warning

Installing an AC Power Supply Module

Follow these steps to install an AC power supply module:

Procedure

Step 1

Ensure that the system (earth) ground connection has been made. For ground connection installation instructions,
see the

Installing the Chassis Ground Connection

section.

Step 2

If necessary, remove the blank power supply filler plate from the chassis power supply bay opening, by
loosening the captive installation screws.

Step 3

Grasp the power supply handle with one hand. Place your other hand underneath the power supply, as shown
in the figure below. Slide the power supply into the power supply bay. Make sure that the power supply is
fully seated in the bay.

Installing the Router

29

Installing the Router

Installing an AC power Supply

«
...
27
28
29
30
31
...
»

Summary of Contents for ASR 920-24SZ-IM























































Reviews:

No comments

Related manuals for ASR 920-24SZ-IM

Brand: Icidu Pages: 10

Brand: Parkside Pages: 55

Brand: Parkside Pages: 34

Brand: Tripp Lite Pages: 20

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

Brand: Edgewater Networks Pages: 7

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: Digital Equipment Pages: 90

Brand: Orcon Pages: 2

Brand: Lancom Pages: 79

Brand: X-Micro Pages: 24

DSL906 1DA Series

Brand: Aztech Pages: 15

Aironet 1430 Series

Brand: Cisco Pages: 48

Aironet 1250 Series

Brand: Cisco Pages: 36

Aironet 1400 Series

Brand: Cisco Pages: 106

Aironet 1250 Series

Brand: Cisco Pages: 142

Aironet 1400 Series

Brand: Cisco Pages: 286

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands