Cisco ASR 920-24SZ-IM Installing Download Page 1

Page: 1 / 54

Installing the Router

This chapter describes how to install the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M
Router.

•

Prerequisites, on page 1

•

Installing the Router in a Rack, on page 1

•

Wall Mounting the Routers, on page 11

•

Installing and Removing the Interface Module, on page 14

•

Installing and Removing the Fan Tray, on page 18

•

Installing the Power Supply, on page 22

•

Installing and Removing SFP Modules, on page 34

•

Connecting to the 10/100/1000 Ports, on page 38

•

Installing the Chassis Ground Connection, on page 40

•

Connecting a Router to the Network, on page 44

Prerequisites

Before installing the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router, it is important
to prepare for the installation by:

• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP).

See

Site Planning

section.

• Unpacking and inspecting the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router.

See

Receiving the Router

section.

• Gathering the tools and test equipment required to properly install the Cisco ASR 920-24SZ-IM,

ASR-920-24SZ-M, ASR-920-24TZ-M Router. See

Tools and Equipment

section.

For more instructions on how to prepare for the installation of the Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M,
ASR-920-24TZ-M Router, see Chapter 2,

Preparing for Installation

Installing the Router in a Rack

The procedures in this section apply to both horizontal and vertical mounting of the router in a rack.

Installing the Router

Summary of Contents for ASR 920-24SZ-IM























































Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands

Cisco ASR 920-24SZ-IM, Installing

Search results

Summary of Contents for ASR 920-24SZ-IM

Reviews:

Related manuals for ASR 920-24SZ-IM

Brands by name

Popular brands