manualshive.com logo in svg

Cisco ASR 920-24SZ-IM, Installing

The Cisco ASR 920-24SZ-IM is a high-performance networking solution designed for efficient data transmission. Simplify your installation process with our comprehensive user manual, available for free download at manualshive.com. This manual provides step-by-step instructions on deploying and configuring the ASR 920-24SZ-IM, ensuring hassle-free implementation and optimal network performance.

Share
Download
background image

Note

Procedure

Step 1

Mount the router with the front panel as shown in the following figures.

The following figures show the wall installation of Cisco ASR-920-24SZ-IM Router and the wall installation
of Cisco ASR-920-24SZ-M, ASR-920-24TZ-M Router.

Figure 12: Mounting the Cisco ASR-920-24SZ-IM Router on the Wall

Drip tray for Cisco ASR-920-24SZ-IM Router

1

Installing the Router

13

Installing the Router

Mounting Routers on the Wall

Summary of Contents for ASR 920-24SZ-IM























































Reviews:

No comments

Related manuals for ASR 920-24SZ-IM

D-Link DIR-855L Quick Installation Manual preview
DIR-855L
Brand: D-Link Pages: 28
D-Link DIR-826L Quick Install Manual preview
DIR-826L
Brand: D-Link Pages: 2
D-Link DIR-655 - Xtreme N Gigabit Router Wireless Quick Start Manual preview
DIR-655 - Xtreme N Gigabit Router Wireless
Brand: D-Link Pages: 3
D-Link DIR-605L Technical Support Setup Procedure preview
DIR-605L
Brand: D-Link Pages: 11
D-Link DIR-822 Quick Instillation Manual preview
DIR-822
Brand: D-Link Pages: 35
D-Link DIR-880L Quick Install Manual preview
DIR-880L
Brand: D-Link Pages: 12
D-Link DIR-842 Quick Install Manual preview
DIR-842
Brand: D-Link Pages: 12
D-Link DIR-821 Quick Install Manual preview
DIR-821
Brand: D-Link Pages: 24
D-Link DIR-803 Quick Installation Manual preview
DIR-803
Brand: D-Link Pages: 20
D-Link DIR-815/AC Quick Installation Manual preview
DIR-815/AC
Brand: D-Link Pages: 44
D-Link DIR-830M Quick Installation Manual preview
DIR-830M
Brand: D-Link Pages: 52
D-Link DIR-821 User Manual preview
DIR-821
Brand: D-Link Pages: 103
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
Delta Electronics Ethernet Communication Module DVPEN01-SL Manual preview
Ethernet Communication Module DVPEN01-SL
Brand: Delta Electronics Pages: 54
Caimore CM520-86EG User Manual preview
CM520-86EG
Brand: Caimore Pages: 79
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56

Brands by name

Popular brands

Load more brands