Cisco ASR 920-24SZ-IM Installing Download Page 28 | Manualshive

Page: 28 / 54

background image

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Follow these steps to remove and replace the DC power supply on the Cisco ASR 920-24SZ-IM,
ASR-920-24SZ-M, ASR-920-24TZ-M Router:

Procedure

Step 1

Before servicing the power supply, switch off the circuit breaker in your equipment area. As an additional
precaution, tape the circuit-breaker switch in the Off position.

Step 2

Slip on the ESD-preventive wrist strap that was included in the accessory kit.

Step 3

Switch the power supply circuit-breaker switch to the Off (O) position.

Step 4

Pull the terminal block plug connector out of the terminal block head in the power supply.

Step 5

Loosen the captive screw on the DC power supply. See the figure below.

Figure 23: Removing a DC Power Supply

Do not use the captive installation screw to pull out the power supply.

Caution

Installing the Router

28

Installing the Router

Removing and Replacing a DC Power Supply

«
...
26
27
28
29
30
...
»

Summary of Contents for ASR 920-24SZ-IM























































Reviews:

No comments

Related manuals for ASR 920-24SZ-IM

Brand: Vanguard Pages: 121

Brand: H3C Pages: 77

Brand: ICP DAS USA Pages: 8

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: Planet Pages: 2

Brand: Zhone Pages: 53

WebShare 141 WN

Brand: Atlantis Pages: 78

RouterBOARD RB711-5HnD

Brand: MikroTik Pages: 2

Magnum mP62-5V -1M1SSC

Brand: GarrettCom Pages: 40

Brand: Foscam Pages: 92

Brand: Fibrain Pages: 20

Brand: Billion Pages: 100

Brand: Cisco Pages: 160

Brand: D-Link Pages: 2

Brand: D-Link Pages: 69

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 170

Brand: H3C Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands