Cisco 3700 series Hardware Installation Manual Download Page 86

Page: 86 / 114

A-6

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Appendix A Troubleshooting

Reading Rear Panel LEDs

The LEDs on the rear panel of the router enable you to determine router performance and operation.

Figure A-3

and

Figure A-4

show the LEDs on the rear panel of the router. For an explanation of these

LEDs, see

Table A-3

and

Table A-4

Figure A-3

Cisco 3725 Router Rear-Panel LEDs

SYS PS1
and
SYS PS2

Off

Power supply not present, or failed.

Solid green

Power supply installed and operating normally.

Amber

Power supply installed and powered off, or fault condition
detected.

–48V PS1
and
–48V PS2

Off

–48-V power module not present, or failed.

Solid green

–48-V power module installed and operating normally.

Amber

–48-V power module installed and powered off, or fault
condition detected.

Table A-2

Cisco 3745 Router Front-Panel Indicators

LED Indicator

State

Description

Table A-3

Cisco 3725 Router Rear-Panel Indicators

LED Indicator

State

Description

Off

CompactFlash (CF) memory card can be
ejected; device is idle.

Solid or blinking green Do not eject the CF; it is busy.

Fast Ethernet 0/0 ACT
and
Fast Ethernet 0/1 ACT

Off

Interface not receiving packets.

Solid or blinking green Interface receiving packets.

Fast Ethernet 0/0 LINK
and
Fast Ethernet 0/1 LINK

Off

No link established.

Solid green

Link is established.

72133

SEE MANU

AL BEFORE INST

ALLATION

SEE MANU

AL BEFORE INST

ALLATION

DSU
56K

SEE MANU

AL BEFORE INST

ALLATION

DSU
56K

BANK 4

BANK 3

BANK 2

BANK 1

BANK 0

NM-HDV

VWIC

2MFT-E1

SEE
MANUAL

BEFORE

INSTALLAT

ION

CTRLR E2

CTRLR E1

FastEthernet 0/1

FastEthernet 0/0

Summary of Contents for 3700 series



















































































































Search results

Summary of Contents for 3700 series

Reviews:

Related manuals for 3700 series

Brands by name

Popular brands

Cisco 3700 series, Hardware Installation Manual

Search results

Summary of Contents for 3700 series

Reviews:

Related manuals for 3700 series

Brands by name

Popular brands