Cisco 3700 series Hardware Installation Manual Download Page 90

Page: 90 / 114

A-10

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Appendix A Troubleshooting

Error Messages

PS1, PS2,
LED on
power
supply rear
panel

Amber

Error:

%PS-3-DCOUTPUTVOLTFAIL: System detected Power System # DC FAIL condition.

Explanation:

The cable connected to the specified DC power supply (1 or 2) is loose, or the DC power
supply has failed.

Recovery:

Check the power supply LEDs to identify the faulty unit.

Power down the faulty power supply and circuit breaker.

Check that cables are seated properly and terminal blocks are wired correctly.

Power up the circuit breaker and the power supply.

If the error condition persists, replace the power supply. (For Cisco 3745 routers, see the

Installing Field-Replaceable Units in Cisco 3745 Routers

hardware configuration note.

For Cisco 3725 routers, see the

Installing Universal DC Power Supplies in Cisco 3725

Routers

hardware configuration note that shipped with the new power supply.)

When the error condition is resolved, the following informational message appears:

%PS-3-DCOUTPUTVOLTOK: Power System DC condition is now normal.

PS1, PS2,
LED on
power
supply rear
panel

Amber

Error:

%PS-3-INPUTVOLTFAIL: System detected Power System # AC FAIL condition.

Explanation:

The cable connected to the specified AC power supply (1 or 2) is loose, or the AC power supply
has failed.

Recovery:

Check the power supply LEDs to identify the faulty unit.

Power down the faulty power supply.

Check that the power cables are seated properly.

Power up the power supply.

If the error condition persists, replace the power supply. (For Cisco 3745 routers, see the

Installing Field-Replaceable Units in Cisco 3745 Routers

hardware configuration note.

For Cisco 3725 routers, see the

Installing AC Power Supplies in Cisco 3725 Routers

hardware configuration note that shipped with the new power supply.)

When the error condition is resolved, the following informational message appears:

%PS-3-INPUTVOLTOK: Power System AC condition is now normal.

Table A-5

System Error and Recovery Messages (continued)

LED Type

LED Color

Message

Summary of Contents for 3700 series



















































































































Search results

Summary of Contents for 3700 series

Reviews:

Related manuals for 3700 series

Brands by name

Popular brands

Cisco 3700 series, Hardware Installation Manual

Search results

Summary of Contents for 3700 series

Reviews:

Related manuals for 3700 series

Brands by name

Popular brands