Cisco 3700 series Hardware Installation Manual Download Page 26 | Manualshive

Page: 26 / 114

background image

1-6

Cisco 3700 Series Routers Hardware Installation Guide

OL-2180-08

Chapter 1 Overview of Cisco 3700 Series Routers

Interface Numbering

Figure 1-3

WAN and LAN Interface Numbering

The slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for physical
slot identification only.) Interfaces in the WICs are numbered from right to left, starting with 0/0 for each
interface type, regardless of which physical slot the WICs are installed in. Some examples are as follows:

•

If slot W0 is empty and slot W1 contains a 1-port serial WIC, the serial interface in the WIC is
numbered Serial 0/0.

•

If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, the serial interfaces
in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the serial interface in physical slot
W1 is numbered Serial 0/2.

•

If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port BRI WIC, the serial interfaces
in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the BRI interface in physical slot
W1 is numbered BRI 0/0.

Voice Interface Numbering

Voice interfaces are numbered as follows:

chassis-slot/voice-module-slot/voice-interface

If a 4-channel voice network module is installed in chassis slot 1, the voice interfaces are:

•

1/0/0—Chassis slot 1/Voice module slot 0/Voice interface 0

•

1/0/1—Chassis slot 1/Voice module slot 0/Voice interface 1

•

1/1/0—Chassis slot 1/Voice module slot 1/Voice interface 0

•

1/1/1—Chassis slot 1/Voice module slot 1/Voice interface 1

Serial 0/2

Compact

Flash slot

56482

SEE MANU

AL BEFORE INST

ALLATION

AL

CD

LP

RD

TD

SEE MANU

AL BEFO

RE INST

ALLATION

DSU
56K

AL

CD

LP

RD

TD

SEE MANU

AL BEFO

RE INST

ALLATION

DSU
56K

EN

V0

BANK 4

BANK 3

BANK 2

BANK 1

BANK 0

NM-HDV

VWIC

2MFT-E1

SEE
MANUAL

BEFORE

INSTALLAT

ION

CTRLR E2

CTRLR E1

AL

LP

CD

Gigabit Ethernet 2/1

Fast Ethernet 2/35

Fast Ethernet 2/17

Gigabit Ethernet 2/0

Fast Ethernet 2/0

Fast Ethernet 2/18

Serial 0/1
Serial 0/0

TI 1/1

TI 1/0

Fast Ethernet 0/1

Fast Ethernet 0/0

BRI 0/0

1

2

«
...
24
25
26
27
28
...
»

Summary of Contents for 3700 series



















































































































Reviews:

No comments

Related manuals for 3700 series

Brand: NetComm Pages: 16

V-NET PLNWKB000

Brand: LG Pages: 19

Brand: LG Pages: 23

V-NET PLNWKB000

Brand: LG Pages: 183

Brand: LG Pages: 11

Brand: Aluratek Pages: 63

Brand: Zoom Pages: 2

Brand: Elesign Pages: 10

Brand: R9 Technology Pages: 5

Brand: PR Elecronics Pages: 24

Brand: gefran Pages: 2

Brand: TVILIGHT Pages: 15

Brand: WePresent Pages: 68

Brand: SmartRG Pages: 18

Brand: Kiwi Pages: 67

Brand: Forum Pages: 20

Brand: Netphonic Pages: 46

Brand: RTA Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands