Circo G20 Installation Manual Download Page 13

Page: 13 / 36

English

I NS TAL LAT ION M ANUA L

5.10 Glass pane

!Caution

Avoid damaging the pane during removal/placing;

Avoid/remove fingerprints on the glass pane, as they will burn into the glass.

5.10.1 Removing the glass pane

When removing the front glass pane, you should follow the next steps:

Open the left (see Appendix 3, Fig. 5 (C)) and right side panel (D);

Loosen the 2 bolts (see Appendix 3, Fig. 8 (P)) of the top panel (G) by a few strokes;

!Caution

Do not completely remove the bolts.

Slide the top panel (G) upwards a little bit, so some play is created in relation to the glass pane.

Loosen the bolt (see appendix 3, fig. 7 (T)) by a few turns.

Fully unscrew the 2 bolts and nuts (see Appendix 3, Fig. 7 (Q)) of the front panel (B);

Remove the front panel (B);

Fully unscrew the 3 nuts (see Appendix 3, Fig. 9 (R)) in the left glass strip and the 3 nuts (R) in the right glass strip;

Remove the left and right glass strip (E and F);

!Caution

Hold the glass pane in the middle, so it cannot fall out.

Slightly move the bottom side of the glass pane towards you and remove the glass pane (see Appendix 3, Fig. 10).

5.10.2 Placing the glass pane

Placing the glass pane will take place in reverse order of removing the glass pane, as described above.

!Caution

Avoid/remove fingerprints on the glass pane, as they will burn into the glass.

Do not overtighten the bolts and nuts, since otherwise they could break or strip the thread: tight=tight;

!Caution

Check whether the insulating rope is neatly around the slot of the combustion chamber.

When placing back the glass pane, observe the following instructions:

Slowly slide the glass pane upwards back to its location and allow the glass pane to rest on the lower strip;

Make sure the glass pane is placed exactly in the middle of the appliance (see Appendix 3, Fig. 11).

!Caution

Keep holding the glass pane in the middle, so it does not fall back.

!Tip

First fasten the left side of the front panel (B) when placing it back, pull the front panel around the glass pane
using the tensioning bolt (T) and then fasten the right side.

5.11 Setting the appliance

The appliance has to be set in such a way that it works correctly in combination with the discharge system used.
For that purpose, a restrictor slide is placed and/or an air inlet guide is removed. The conditions for application
with wall terminal and roof terminal are stated in appendix 2, tables 4, 5 and 6.

5.11.1 Air inlet guide

The air inlet guide (L) is located at the back at the bottom of the appliance's combustion chamber
(see Appendix 3, Fig. 12 and 13).
If you want to remove it, proceed as follows:

Remove the glass pane as described in section 5.10.1.

Fully unscrew the 2 bolts of the top panel (G), (see Appendix 3, Fig. 8 (P));

Remove the top panel (G);

Slide the back panel (see Appendix 3, Fig. 12 (H)), which is fixed with 4 hooks in 4 slots, upwards and remove it;

!Caution

The decoration ring is hitched to the back panel. Make sure the decoration ring remains at its location when
removing the back panel (H).

Completely unscrew the 2 self-tapping screws of the lower cover plate (I);

Remove the lower cover plate from the appliance;

Unscrew the 2 self-tapping screw at the back of the appliance and remove them (see Appendix 3, Fig. 13);

Now remove the air inlet guide (L) from the inside;

!Caution

Close the two holes created by removing the 2 self-tapping screws, using the supplied sealing caps
(see Appendix 3, Fig. 13);