Circo G20 Installation Manual Download Page 12

Page: 12 / 36

English

I NS TAL L ATI O N MA N U A L

5.9 Additional instructions

!Tip

It will be easier to reach the gas control, if you remove the front panel

5.9.1 Placing the appliance

When placing the appliance, please take the following aspects into account:

Make sure the appliance is stable and level it using the adjustable feet (see Appendix 3, Fig. 5 (K)).

!Caution

Maintain a minimum distance of 40 mm between the appliance and the back wall (see Appendix 3, Fig. 2).

5.9.2 Gas connection

At the back of the appliance you will find a round plate that can be removed by pressing on it, for the benefit of
the gas connection (from the wall). However, it is also possible to make the gas connection (from the floor) via the
bottom side of the appliance.

!Tip

When installing an appliance where the air inlet guide has to be removed, you should remove the air inlet guide
before connecting the gas pipe. In reverse order, it will be difficult to remove the back plate. This problem only
occurs in case of a gas connection via the round recess at the back of the appliance and not in case of a
connection via the bottom side.

Make sure there is no dirt in gas pipes and connections;

Connect the gas pipe to the gas tap;

Bleed the gas pipe;

Place the receiver for the remote control (see section 5.9.3).

5.9.3 Placing the receiver

The appliance is equipped with an electronic ignition through the remote control. The receiver should be placed
in the appliance. Follow the procedure described below:

Stand on the left side of the appliance, in front of the left side panel (see Appendix 3, Fig. 5 (C)).

!Caution

The side panels (C and D) have their hinges at the back of the appliance.

Open the left side panel (C) by grabbing it at the bottom and as far as possible to the right (glass pane side) and
pulling it towards you;

!Caution

The side panels open and close by means of a snap-on system (S). When opening and closing the panels you could
experience some resistance. That is normal.

Put the receiver at the right location (see Appendix 3, Fig. 6);

Connect the receiver to the appliance according to the instructions in section 6.1;

Close the left side panel (C) by carefully pressing the panel in the snap connections.

5.9.4 Placing the decoration ring

The decoration ring (see Appendix 3, Fig. 8 (A)) lies on the ground and provides the connection of the appliance to
the floor.
Place the decoration ring as follows:

Open the left side panel (see Appendix 3, Fig. 5 C));

Open the right side panel (D) by grabbing it at the bottom and as far as possible to the left (glass pane side) and
pulling it towards you.

Loosen the bolt (see appendix 3, fig. 7 (T)) by a few turns.

Unscrew the 2 bolts and 2 nuts (see Appendix 3, Fig. 7 (Q)) from the front panel (B), which is located below the
glass pane.

Remove the front panel (B).

Place the round decoration ring (see Appendix 3, Fig. 8 (A)) by hitching it to the back panel (H).

!Caution

Do not bend the round decoration ring open towards the outside by means of both hands. Else the ring could lose
its round shape. Carefully guide the decoration ring around the appliance's adjustable feet. Foot by foot, towards
the left OR towards the right.

Place back the front panel (B), by:

tightening the bolt and nut at the left side;

pulling the front panel around the glass pane, using the tensioning bolt (T);

tightening the bolt and nut at the right side.

!Tip

Only place back the front panel once the log set has been placed.

Close the left and right side panels, by carefully pressing them in the snap connections until they are closed.