background image

24

23

Care and Maintenance

In order to avoid any harm to the users or others during 
usage and prolong the usage life, please abide by the 
following notices. 

Maintenance

You can get most dust or fingerprint off with a dry, soft cloth 
or tissue. If there is dirt on the keypad, please wipe the 
surface by a soft cloth with a little dilute alkaline detergent 
and then wipe again with a dry cloth. 

Problem

FAQ

Cause

Solution

No response 
from keypad

Low battery

The positive and 

negative terminals 

are reversed

Keypad is locked by 

inputting wrong 

passcode continually 

more than 6 times

Please change the battery

Follow the right terminal direction and 

inert the battery again

Keypad will be unlocked after 

non-operation for 20 seconds

Keypad 
cannot 
connect to 
control panel

No response from 

alarm panel

Alarm panel beeps 

twice

Make sure the alarm panel is 

powered on

Make sure the alarm panel enters 

learning state

Keypad has been learned

No response 
from the 
control panel 
by operating 
on keypad

Keypad is not learned 

to control panel

Distance between 

keypad and control 

panel is too far

Please connect the keypad to the 

control panel by following the manual 

instruction

Please move the keypad in a proper 

distance where control panel can 

receive the signal of keypad

It’s recommended to buy signal 

repeater to extend the distance

Cannot 
disarm by 
RFID Tags

The RFID tags are not 

learned to keypad

Disarm by RFID tag 

function is deactivated.

Keypad is in power 

saving mode

Please connect the RFID tag to 

control panel by following the 

manual instruction

Enter setup state and activate the 

function of disarm by RFID tag 

Disarm after pressing [*] key

Keypad 
cannot be 
programmed

Keypad is not waked 

up

Keypad doesn’t enter 

setup state

Please input [admin code+#] to wake 

up the keypad

Please input [admin code+#], and 

press [3] to enter setup state

Keypad 
cannot be 
armed, 
disarmed and 
in stay mode

Haven't input user 

code or admin code 

before operation

Please input the user code or admin 

code before operation

Usage Notices

The keypad should be connected to control panel before use.

The power supply of keypad will probably impact on the transmitting distance 
of wireless signal.

The keypad can be powered by 3 pcs of AAA batteries, or wired by DC 12V.

The keypad is compatible for any our alarm system.

Please remove the battery insulating strip before use.

Do not press SOS key if there's no emergency to avoid disturbing the 
neighborhood.

Check the keypad regularly to ensure the system works properly in case of 
emergency. 

The keypad is neither waterproof nor moisture-proof, please install it in a 
shady, cool and dry place.

The case of keypad is made of ABS. Please keep it away from strong light to 
ensure the lifetime.

The keypad is non explosion-proof. Please keep it away from fire, flame sources. 

Install the keypad away from objects such as heater, air conditioner, 
microwave oven etc. that produces heat or electric-magnetic.

Take the keypad for disposal of recycling according to the local regulation.

Do not take apart the product if you are not a professional technician.

General instruction

Forbiddance

Forbiddance of decomposition

Summary of Contents for KP-700
















Reviews: