background image

1.

5

6

2.

AAA

+

+

1.

Preparation before Use

Power on

Keypad uses 3pcs of AAA batteries.

Loose the screw, open the case

Put in batteries according to the positive and negative signs

Close the rear cover and screw on

Remove the insulating strip for first time.

Note! 

Open the rear cover of keypad will trigger tamper switch, please 

dismiss the alarm by following the disarm instruction in page 20.

When connected with electronic door lock as an access control, 

keypad is suggested to use the specific power supply for access 

control.

To know connection steps, please refer to the instruction manual of electronic 

door lock. The electronic door lock and specific power supply for access control 

should be purchased respectively.

Connect Keypad to Control Panel

Make sure the control panel is in connecting state, input user 

code or admin code on keypad, and then press any key of 

. The connection succeeds after 

one beep.

[Arm] [Disarm] [Stay Mode]

User can remotely control the panel via the keypad after connection.

(To know connection steps, please consult the panel’s manual.)

Connect Keypad with RFID Tag

Input 

 to wake up keypad.

Three beeps mean wrong input.

[admin code   + #]

Wrong input for 6 times continuously, the keypad will be locked for 20 seconds.

Default admin code: 123456

Summary of Contents for KP-700
















Reviews: