background image

 
 

each run if it has the 120 Ω 
terminating resistor. 

 

Specification 

 
Technical Specifications 

 

Net Dimensions** 
(Without Fixings - Width 
x Height x Depth) 

483mm x 88mm x 254mm / 19” x 3.5” x 10” 

Net Weight (Without 
Fixings) 

2.5kg / 5.5lb 

Shipping Dimensions 

–  

Width x Height x Depth 

533mm x 317.5mm x 133.5mm / 21” x 12.5” x 5.25” 

Shipping Weight 

3.3kg / 7.3lb 

Power & Connections 

  

Power Supply 

Built-in 

Power Input Rating 

100-240V AC 50-60Hz .4A 

Power Factor 

0.6 

Power Consumption 

4.6W @ 120V AC; 9W @ 230V AC 

Inrush Current 

11A @ 120V AC; 23A @ 230V AC 

Idle Power Consumption 

4.6W @ 120V AC; 9W @ 230V AC 

Typical Power & Current 

Measurements done with all LEDs at maximum intensity. Measurements 
made at nominal voltage. Allow for a deviation of +/- 10%. 

Power connector In/Out 

Input only: Internal Terminal Block; Transfer Power Input from 
Generator: Internal Terminal Block 

Data Connectors In/Out 

Terminal Block 

Control Protocol 

ANSI E1.11 USITT DMX 512-A 

Cooling System 

Convection 

Operating Temperature 

0°C to 40°C 

Construction 

Powder-coated aluminium  

Colour 

Black 

IP Rating 

IP20 

Approvals  

CISPR 22/EN55022 & CISPR 24/EN55024, ICES-003 Issue 4:2012 / 
FCC Part 15 Subpart B:2014, CSA C22.2 No. 166-M1983: R2013, UL 
1573:2003 R2014, IEC 60598-2-17, UL924 

Control 

  

Control Modes 

RGBW single, RGBW output, Tungsten, 0-10V , LookStore 

Dimming Curve 

Theatrical 

 

 

 

 

 

 

Summary of Contents for Inspire UL924























Reviews: