Chroma 63200A Series Operation & Programming Manual Download Page 75

Page: 75 / 141

High Power Electronic Load 63200A Series Operation & Programming Manual

4-12

Query Example:

CONF:SYNC:MODE?

CONFigure:PARAllel:INITial

Type:

All Channel

Description:

Set Load into/exit parallel mode.

Setting Syntax:

CONFigure:PARAllel:INITial<space><CRD | NR1>

Setting Parameters: <CRD | NR1>, OFF(0), ON(1)

Setting Example: CONF:PARA:INIT ON

Set Load to into parallel mode.

CONF:PARA:INIT 0

Set Load to exit parallel mode.

Query Syntax:

CONFigure:PARAllel:INITial?

Return Parameters:<CRD>, OFF(0), ON(1)

[Unit = None]

Query Example:

CONF:PARA:INIT?

CONFigure:PARAllel:MODE

Type:

Channel-Specific

Description:

Set the parallel mode.

Setting Syntax:

CONFigure:PARAllel:MODE<space><CRD | NR1>

Setting Parameters: <CRD | NR1>, NONE(0), MASTER(1), SLAVE(2)

Setting Example: CONF:PARA:MODE MASTER

Set parallel mode to MASTER.

CONF:PARA:MODE 0

Set parallel mode to NONE.

Query Syntax:

CONFigure:PARAllel:MODE?

Return Parameters:<CRD>, NONE(0), MASTER(1), SLAVE(2) [Unit = None]

Query Example:

CONF:PARA:MODE?

CONFigure:AUTO:ON

Type:

Channel-Specific

Description:

Set the load module to perform auto load on during power-on.

Setting Syntax:

CONFigure:AUTO:ON<space><CRD | NR1>

Setting Parameters:<CRD | NR1>, OFF(0), ON(1)

Setting Example: CONF:AUTO:ON ON

Set auto load on state to ON.

CONF:AUTO:ON 0

Set auto load on state to OFF.

Query Syntax:

CONFigure:AUTO:ON?

Return Parameters:<CRD>, OFF(0), ON(1) [Unit = None]

Query Example:

CONF:AUTO:ON?

CONFigure:ENTer:KEY

Type:

Channel-Specific

Description:

Set the action type of ENTER key.

Setting Syntax:

CONFigure:ENTer:KEY<space><CRD | NR1>

Setting Parameters: <CRD | NR1>, NEXT(0), FIXED(1)

Setting Example: CONF:ENT:KEY NEXT

Set ENTER key function to NEXT.

CONF:ENT:KEY 1

Set ENTER key function to FIXED.

Query Syntax:

CONFigure:ENTer:KEY?

Return Parameters: <CRD>, NEXT(0), FIXED(1)

[Unit = None]

Query Example:

CONF:ENT:KEY?

CONFigure:SHORt:KEY

Type:

Channel-Specific

Description:

Set the action enable or disable of SHORT key.

Setting Syntax:

CONFigure:SHORt:KEY<space><CRD | NR1>

Setting Parameters: <CRD | NR1>, HOLD(0), TOGGLE(1) , DISABLE(2)
Setting Example: CONF:SHOR:KEY DISABLE

Set SHORT key function to
disable.

Summary of Contents for 63200A Series














































































































































Search results

Summary of Contents for 63200A Series

Reviews:

Related manuals for 63200A Series

Brands by name

Popular brands

Chroma 63200A Series, Operation & Programming Manual

Search results

Summary of Contents for 63200A Series

Reviews:

Related manuals for 63200A Series

Brands by name

Popular brands