Christie Roadie 4K35 Service Manual Download Page 78

Page: 78 / 87

11. Disconnect the live, neutral and ground wires. Transfer to new low voltage power supply

(LVPS)

12. Remove the four screws securing the LVPS to the bracket.

13. Transfer all harnesses to the new LVPS.
14. Make note of where each connection is located.
15. To install the LVPS, repeat these steps in reverse order.

Replacing the standby power supply

Estimated replacement time: 12 minutes

1. Remove the low voltage power supply (LVPS) (on page 77).
2. Loosen the thumbscrew securing the standby power supply.

3. Disconnect and remove the standby power supply.
4. To install the standby power supply, repeat these steps in reverse order.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands