Christie Roadie 4K35 Service Manual Download Page 52 | Manualshive

Page: 52 / 87

background image

4. Remove the HIP fan.
5. Replace the HIP fan.
6. To re-install the HIP fan, follow these steps in reverse order.

Replacing the liquid cooling pump fan (fan #14)

Estimated replacement time: 16 minutes per fan

1. Remove the liquid cooling module (on page 54).
2. Disconnect the fan inline connector.
3. Remove the two screws securing the fan.

4. Remove the liquid cooling pump fan.
5. Replace the liquid cooling pump fan.
6. To secure the liquid cooling pump fan, follow these steps in reverse order.

Replacing the IMCB fan (fan #18)

Estimated replacement time: 5 minutes

1. Remove the touch panel controller (on page 39).
2. Remove the rear cover (on page 44).
3. Disconnect the fan connector.
4. Remove the four screws securing the fan.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

52

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
50
51
52
53
54
...
»

Summary of Contents for Roadie 4K35
























































































Reviews:

No comments

Related manuals for Roadie 4K35

Brand: Lampo Pages: 2

Brand: Black Box Pages: 2

Brand: Sinew Pages: 44

Brand: FujiFilm Pages: 20

BrilliantColorPanel BCP100

Brand: ViewSonic Pages: 2

Brand: M-system Pages: 5

Brand: Hitachi Pages: 40

Brand: CHINON Pages: 8

Brand: Optoma Pages: 2

Brand: Mitsubishi Electric Pages: 34

Brand: Mitsubishi Electric Pages: 9

Brand: Mitsubishi Electric Pages: 5

Brand: Mitsubishi Electric Pages: 6

Brand: Mitsubishi Electric Pages: 2

Brand: Mitsubishi Electric Pages: 39

Brand: Mitsubishi Electric Pages: 34

Brand: Mitsubishi Electric Pages: 40

Brand: Mitsubishi Electric Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands