Christie Roadie 4K35 Service Manual Download Page 31

Page: 31 / 87

Troubleshooting

The following topics cover common projector issues and their solutions.
If an issue cannot be resolved, contact a Christie qualified technician.

Projector does not power on

The projector is connected to AC power but does not power on.

Resolution

•

Make sure that all three circuit breakers on the lamp power supply (LPS) are turned on.

•

Make sure the projector circuit breaker is set to the on position.

•

Check the status LEDs on the rear corners of the projector for a fault condition. A flashing red
LED indicates an alarm or warning preset with the projector and a problem that must be
addressed.

•

Use the touch panel controller (TPC) status menu to troubleshoot further.

Lamp does not ignite

The projector is powered on but the lamp does not ignite.

Resolution

•

Make sure all three breakers on the lamp power supply (LPS) are set to their on positions.

•

Check and correct all interlock failures.

•

Check the lamp power supply communication connections and restart the projector.

•

Verify that the lamp has been installed and connected properly. Verify the condition of the
lamp and that is not blackened or otherwise damaged.

•

Verify the number of hours the lamp has operated. A lamp nearing the end of its operational
life should be replaced.

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands