Christie Roadie 4K35 Service Manual Download Page 41

Page: 41 / 87

3. Tilt the front cover towards the front of projector to clear tabs, lift the cover, and remove.
4. To re-install, follow these steps in reverse order.

Removing the light engine cover

Remove the light engine cover to access the light engine.
Estimated replacement time: 1 minute

Notice. Failure to comply with the following may result in property damage.

•

Christie products must be installed and serviced by Christie qualified technicians.

1. Remove the front cover (on page 40).
2. Using the security key, unlock the light engine cover.

3. Lift up the cover and remove.
4. To re-install, follow these steps in reverse order.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands