manualshive.com logo in svg

Christie CA20-AC, Installation And Setup Manual

Share
Download
Christie CA20-AC Installation And Setup Manual Download Page 35

16. Tighten the two screws (A in the image below) installed in step 6.

17. Install two additional screws (B in the image in step 16) to secure the receiver box.
18. Connect to power (on page 24).

•

For the UL version if a conduit is being installed, remove the pre-installed power cable and
directly wire the AC to the terminal block in the fixture.

•

For the CE version, no pre-installed power cable is supplied.

19. Install the disinfecting module in the receiver box (on page 17).
20. Install the ceiling tiles removed in step 2.
21. Repeat steps 1 to 20 for each receiver box.

Mounting receiver boxes with the pendant option

Pendant mounting works with swing bracket (P/N: 174-105107-XX) or an equivalent mounting fixture.
This is an optional mounting option available for purchase from a Christie equipment provider.

Installation and setup

CounterAct Installation and Setup Guide

35

020-103456-02 Rev. 1 (12-2021)

Copyright 

©

 2021 Christie Digital Systems USA, Inc. All rights reserved.

Summary of Contents for CA20-AC





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands