Christie Boxer 30 Service Manual Download Page 37

Page: 37 / 113

4. If required, replace the bottom cover.
5. To install the bottom cover, repeat these steps in reverse order.

Replacing a projector's foot

The adjustable feet can be raised or lowered when positioning the projector to make sure it is level on

all sides so the displayed image appears rectangular without any keystone.
Estimated replacement time: 3 minutes for servicing a single foot

1. Ensure the projector is in a secure position.

Christie does not recommend having the projector overhang when replacing the feet, unless
the projector is securely positioned.

2. Loosen the lock nut on the affected foot.
3. Uninstall the foot.
4. Replace the foot.
5. To re-install, follow these steps in reverse order.

Projector covers and feet

Boxer 4K Service Guide

020-101699-04 Rev. 1 (02-2018)

Summary of Contents for Boxer 30


















































































































Search results

Summary of Contents for Boxer 30

Reviews:

Related manuals for Boxer 30

Brands by name

Popular brands

Christie Boxer 30, Service Manual

Search results

Summary of Contents for Boxer 30

Reviews:

Related manuals for Boxer 30

Brands by name

Popular brands