Christ 112991 Operating Manual Download Page 133 | Manualshive

Page: 133 / 148

background image

Freeze-dryer Epsilon 1-4 LSCplus

Freeze-dryer Epsilon 2-4 LSCplus

10 Technical data

Version 04/2014, Rev. 2.13 of 01/12/2021

• sb

133 / 148

Translation of the original operating manual

Pos : 286 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/100 T ec hnisc he D at en/100- 0010 Umgebungsbedingungen Ü bers chrift---------------------------------------------- @ 25\mod_1404984155772_68. docx @ 184573 @ 2 @ 1

→

10. 1

Umgebungs beding ung en

10.1 Ambient conditions

Pos : 287 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/100 T ec hnisc he D at en/100- 0011 Umgebungsbedingungen T ext @ 25\m od_1404984154817_68. docx @ 184559 @ @ 1

→

10. 1

Umgebungs beding ung en

•  Use in closed spaces
•  Altitudes up to 2,000 m
•  Ambient temperature b5°C and +25°C
•  Maximum relative humidity of 80%
•  Mains voltage fluctuations of up to ± 10% of the rated voltage

Pos : 288 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 289 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/100 T ec hnisc he D at en/100- 0020 Technisc he Dok um entation @ 25\m od_1404984156884_68.docx @ 184587 @ 2 @ 1

→

10.2 Technical documentation

The technical documentation of this freeze-dryer (e.g. circuit diagram,
cooling system) and the safety data sheets of the manufacturers (e.g. for
refrigerant) is not attached to this operating manual.

You can order these documents from our service department.

Pos : 290 /010 Univ ers almodul e/ Abs chnitt swec hs el @ 0\mod_1202124514062_0. docx @ 418 @ @ 1

Pos : 291 /010 Univ ers almodul e/ Seit enwechs el @ 0\mod_1202116244312_0.docx @ 105 @ @ 1

«
...
131
132
133
134
135
...
»

Summary of Contents for 112991





















































































































































Reviews:

No comments

Related manuals for 112991

Brand: Calistair Pages: 44

Brand: XAG Pages: 24

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brand: LAUNCH TECH Pages: 14

X-431 PROS V4.0

Brand: Launch Pages: 80

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands