Christ 112991 Operating Manual Download Page 39 | Manualshive

Page: 39 / 148

background image

Freeze-dryer Epsilon 1-4 LSCplus

Freeze-dryer Epsilon 2-4 LSCplus

3 Safety

Version 04/2014, Rev. 2.13 of 01/12/2021

• sb

39 / 148

Translation of the original operating manual

• Skin:

Wash with plenty of water. Remove contaminated clothing. Rinse the
affected skin areas under flowing water for at least 10 minutes.

Get

medical attention immediately!

• Oesophagus:

Do not put anything into the mouth of an unconscious person. Wash the
mouth out with water, If the person is conscious: Give the affected
person plenty of water to drink (2 glasses maximum). Do not induce
vomiting. In case of spontaneous vomiting, keep the head of the
affected person lying on his/her stomach low in order to prevent any
liquid from entering the respiratory tract.

Get medical attention

immediately!

IF IN DOUBT; CALL AN EMERGENCY PHYSICIAN!

Pos : 103 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 104 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 105 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/030 Sicherheit/ 030- 0020 Si cherheit Epsilon/ 030-0110 W artung und R einigung der Gefriertr ock nungsanlag e Epsil on @ 36\m od_1436165334319_68. docx @ 267050 @ 2 @ 1

3.10 Maintenance and cleaning of the freeze-dryer

The substances and materials that are used must be properly handled and
disposed of (Please refer to the safety data sheets!). This applies
particularly to
• the handling of solvents, lyes, and acids,
• the changing and topping-up of operating supplies.
Compliance with the national rules and regulations must be ensured.

Pos : 106 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 107 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 108 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/030 Sicherheit/ 030- 0120 An- und Um baut en an der G efrier trock nungs anl age @ 36 \mod_1436165523117_68. doc x @ 267064 @ 2 @ 1

3.11 Additions or conversions of the freeze-dryer

Additions or conversions of the freeze-dryer require the written approval by
Martin Christ Gefriertrocknungsanlagen GmbH.

Pos : 109 /010 Univ ers almodul e/ Seit enwechs el @ 0\mod_1202116244312_0.docx @ 105 @ @ 1

«
...
37
38
39
40
41
...
»

Summary of Contents for 112991





















































































































































Reviews:

No comments

Related manuals for 112991

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: Panasonic Pages: 180

Brand: Zenbooth Pages: 60

Brand: B-K lighting Pages: 3

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: TANDBERG Pages: 23

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brand: laerdal Pages: 32

Brand: laerdal Pages: 32

Brand: laerdal Pages: 8

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands