Christ 112991 Operating Manual Download Page 67 | Manualshive

Page: 67 / 148

Christ 112991 Operating Manual Download Page 67

Freeze-dryer Epsilon 1-4 LSCplus

Freeze-dryer Epsilon 2-4 LSCplus

6 Operation

Version 04/2014, Rev. 2.13 of 01/12/2021

• sb

67 / 148

Translation of the original operating manual

Performance test (1)

The performance test is used to determine the following performance
parameters:
•  vacuum decrease rate
•  final vacuum
•  minimum ice condenser temperature
•  shelf cooling rate
•  minimum shelf temperature
•  shelf heating rate

NOTE

Prior to performing a test, ensure that the chamber is dry and unloaded.

Procedure:
• In the main window "Manual", select the button "Operating mode:

select/start"

– "Standard unit test".

• Select "Performance Test" and start the test via the "Run" button.
The test will be performed. The parameters will be measured at defined
points of time, evaluated, and displayed in a dialog box (see the following
illustration).

If the freeze-dryer is equipped with the LPCplus SCADA software, the
results will be documented in the event list.

Fig. 32: Results of the performance test

Evaluation:

Please contact the Christ support team for the evaluation of the test run.

«
...
65
66
67
68
69
...
»

Summary of Contents for 112991





















































































































































Reviews:

No comments