manualshive.com logo in svg

Chevrolet 2010 Camaro, Owner'S Manual

The Chevrolet 2010 Camaro Owner's Manual is an essential guide for every Camaro owner. Whether you need to troubleshoot a problem or want to learn more about your vehicle's features, this comprehensive manual provides detailed instructions. Download your free copy at manualshive.com and unlock the full potential of your Camaro.

Share
Download
background image

Black plate (87,1)

Chevrolet Camaro Owner Manual - 2010

Vehicle Care

9-87

The jump start positive (A) and
negative (B) posts are located in the
engine compartment on the driver
side of the vehicle.

These posts are used instead of a
direct connection to the battery.

The positive jump start connection
is covered by a red cap. Remove to
expose the terminal.

1. Check the other vehicle. It must

have a 12-volt battery with a
negative ground system.

Notice:

If the other vehicle's

system is not a 12-volt system
with a negative ground, both
vehicles can be damaged. Only
use vehicles with 12-volt systems
with negative grounds to jump
start your vehicle.

2. Position the two vehicles so that

they are not touching.

3. Set the parking brake firmly and

put the shift lever in P (Park).
See

Shifting Into Park on

page 8

‑

22

.

Notice:

If you leave the radio or

other accessories on during the
jump starting procedure, they
could be damaged. The repairs
would not be covered by the
warranty. Always turn off the
radio and other accessories
when jump starting the vehicle.

4. Turn the ignition to LOCK/OFF

and switch off all lights and
accessories in both vehicles,
except the hazard warning
flashers if needed.

Summary of Contents for 2010 Camaro



























































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Camaro

Qube AP1 Supplemental Instructions preview
AP1
Brand: Qube Pages: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Brand: Cadillac Pages: 32
Yakima K1188 Instructions Manual preview
K1188
Brand: Yakima Pages: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Brand: JEHNERT SOUND DESIGN Pages: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Brand: Rainbow Pages: 19
Yakima K1006 Instructions Manual preview
K1006
Brand: Yakima Pages: 12
Allen Sports QR545 Instructions preview
QR545
Brand: Allen Sports Pages: 2
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Brand: Dometic Pages: 196
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Brand: Ecco Pages: 5
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
Caltrend BM110 Installation Instructions preview
BM110
Brand: Caltrend Pages: 2
Advanced ICE 1296-1 Manual preview
1296-1
Brand: Advanced ICE Pages: 4
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
BMW 51 47 0 027 792 Installation Instructions Manual preview
51 47 0 027 792
Brand: BMW Pages: 7

Brands by name

Popular brands

Load more brands