manualshive.com logo in svg

Chevrolet 2010 Camaro, Owner'S Manual

The Chevrolet 2010 Camaro Owner's Manual is an essential guide for every Camaro owner. Whether you need to troubleshoot a problem or want to learn more about your vehicle's features, this comprehensive manual provides detailed instructions. Download your free copy at manualshive.com and unlock the full potential of your Camaro.

Share
Download
background image

Black plate (16,1)

Chevrolet Camaro Owner Manual - 2010

9-16

Vehicle Care

3.6 L V6 Engine Air Cleaner/Filter

Housing shown (6.2 L V8 Engines

similar)

3. Loosen the clamp at the duct of

the air cleaner/filter housing.

4. Unlatch the retaining clips on the

air cleaner/filter housing.

5. Lift cover at retaining clip

location high enough to clear
retaining clips and pull cover
outward to remove cover from
the air cleaner/filter housing
hinges.

6. Pull straight up on cover, while

holding the cover remove the air
filter.

7. Inspect or replace the air filter.

See

Maintenance Replacement

Parts on page 10

‑

11

.

8. Reverse steps 6 to 1 to install

cover.

{

WARNING

Operating the engine with the air
cleaner/filter off can cause you
or others to be burned. The air
cleaner not only cleans the air; it
helps to stop flames if the engine
backfires. Use caution when
working on the engine and do not
drive with the air cleaner/filter off.

Notice:

If the air cleaner/filter is

off, dirt can easily get into the
engine, which could damage it.
Always have the air cleaner/filter
in place when you are driving.

Summary of Contents for 2010 Camaro



























































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Camaro

Abarth 595 Owner'S Handbook Manual preview
595
Brand: Abarth Pages: 176
Caltrend CV445 Installation Instructions preview
CV445
Brand: Caltrend Pages: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Brand: Audiovox Pages: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Brand: EGR Pages: 28
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Brand: Firestone Pages: 4
Whispbar K607W Fitting Instructions Manual preview
K607W
Brand: Whispbar Pages: 14
LXE Akerstroms Tx700 Configuration Manual preview
Akerstroms Tx700
Brand: LXE Pages: 146
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Brand: TATA Motors Pages: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Brand: PAC Pages: 5
Percon Falcon 655 User Manual preview
Falcon 655
Brand: Percon Pages: 49
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Brand: Safe Fleet Pages: 12
N.R. AUTOSEATS Top User Manual preview
Top
Brand: N.R. AUTOSEATS Pages: 8
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
Poison Spyder TrailGate TJ Installation Instructions preview
TrailGate TJ
Brand: Poison Spyder Pages: 5
AllTrade Powerbuilt 648601 Operating Instructions preview
Powerbuilt 648601
Brand: AllTrade Pages: 3
Perrycraft SportQuest Series Installation preview
SportQuest Series
Brand: Perrycraft Pages: 2
Kolpin 1466 Product Instructions preview
1466
Brand: Kolpin Pages: 6
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Brand: Easee Pages: 21

Brands by name

Popular brands

Load more brands