manualshive.com logo in svg

Chevrolet 2010 Camaro, Owner'S Manual

The Chevrolet 2010 Camaro Owner's Manual is an essential guide for every Camaro owner. Whether you need to troubleshoot a problem or want to learn more about your vehicle's features, this comprehensive manual provides detailed instructions. Download your free copy at manualshive.com and unlock the full potential of your Camaro.

Share
Download
background image

Black plate (35,1)

Chevrolet Camaro Owner Manual - 2010

Vehicle Care

9-35

4. At the wall measure from the

ground upward (A) to the
recorded distance from
Step 3 and mark it.

5. Draw or tape a horizontal line (B)

on the wall the width of the
vehicle at the height of the mark
in Step 4.

Notice:

Do not cover a headlamp

to improve beam cut-off when
aiming. Covering a headlamp may
cause excessive heat build-up
which may cause damage to the
headlamp.

6. Turn on the low-beam

headlamps and place a piece
of cardboard or equivalent in
front of the headlamp not being
adjusted. This allows only the
beam of light from the headlamp
being adjusted to be seen on the
flat surface.

Halogen Headlamp

HID Headlamp

7. Locate the vertical headlamp

aiming screws, which are under
the hood near each headlamp
assembly.

The adjustment screw can be
turned with a 6 mm hex key.

8. Turn the vertical aiming

screw until the headlamp beam
is aimed to the horizontal tape
line. Turn it clockwise or
counterclockwise to raise or
lower the angle of the beam.

Summary of Contents for 2010 Camaro



























































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Camaro

Camcar 2155 Fitting Instructions preview
2155
Brand: Camcar Pages: 2
Feniex AM600 Instruction Manual preview
AM600
Brand: Feniex Pages: 6
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
Warrior Products 4560 Manual preview
4560
Brand: Warrior Products Pages: 4
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Brand: Mercedes-Benz Pages: 388
Standby L54 Manual preview
L54
Brand: Standby Pages: 10
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Brand: PUTCO Pages: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Brand: Westfalia Pages: 18
DEFA 412737 Fitting Instructions Manual preview
412737
Brand: DEFA Pages: 7
Prorack K869 Fitting Instructions Manual preview
K869
Brand: Prorack Pages: 15
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Brand: Axxess Pages: 8
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Brand: Safe Fleet Pages: 11
Camec 042374 User Manual preview
042374
Brand: Camec Pages: 19
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
Bestop 614.04 Installation Manual preview
614.04
Brand: Bestop Pages: 31
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Brand: Abrams Pages: 12

Brands by name

Popular brands

Load more brands