Chery SQR477F User Manual Download Page 139

Page: 139 / 163

Maintenance and Upkeep

- 133 -

Central electronics box is located in

miscellany box rear part of the

driver‘s instrument panel.

The circuit all has fuse for protection,

we recommend you carry some spare

fuses to make things convenient for

replacement.

Replacement of fuse

1.Turn the engine and corresponding

electric component off.

2.Remove the screws fixed on both

side of miscellany box, using SST.

3.Check the suspected fuse to see if it

is blown.

4.Pull the blown fuse straight out,

replace with a good one of same

amperage.

5.Electrify

the

corresponding

equipment and check it.

6.Install the miscellany box properly.

！

Notice

If the new fuse immediately blows
out, contact your nearest Chery
Authorized

Service

Station

for

assistance.  Fuse  is  non-reusable,  if
blown,  it  cannot  be  used  again,  do
not  use  the  blown  one  for  it  will
damage the electrical system.

Center electronics box fuse
location diagram

15A

10A

15A

20A

10A

20A

30A

15A

10A

15A

20A

10A

30A

15A

10A

20A

10A

Engine

compartment

relay/Fuses box

There are 3 relay and fuse boxes: one

fuse box is located on the connecting

place of positive boom and the

battery; the other two relay and fuse

boxes are located on front fender of

Summary of Contents for SQR477F




































































































































































Search results

Summary of Contents for SQR477F

Reviews:

Brands by name

Popular brands

Chery SQR477F, User Manual

Search results

Summary of Contents for SQR477F

Reviews:

Brands by name

Popular brands