background image

9

Wire Specifications

Use this chart to pull wires in preparation of your installation. Check the national and local building codes 

BEFORE

 installation.

DESCRIPTION OF WIRE RUN

WIRE SPECIFICATION

MAXIMUM RUN DISTANCE

Power Wire, secondary DC output

2-Conductor 14 AWG
2-Conductor 16 AWG
2-Conductor 18 AWG

Up to 300 feet (91.4 m)
Up to 200 feet (60.9 m)
Up to 100 feet (30.4 m)

Local Area Network (LAN) 

CAT 5e or better Network Cable.

8-Conductor, 24 AWG Twisted pair

328 feet* (100 m)

Grounding the Chassis (use grounding lug in CAPXM)

12 AWG Copper

12 feet (3.7 m)

Door Strike

2-Conductor 18-22 AWG Shielded

100 - 250 feet (30.5 - 76.2 m)

Magnetic Lock

2-Conductor 18-22 AWG

50 - 125 feet (15.2 - 38.1 m)

Dry Contact Closure (Most Gate Operators)

2-Conductor 18-24 AWG Shielded

500 - 2500 feet (152.4 - 762 m)

Exit Request (REX) 

2-Conductor 18-24 AWG

500 feet (152.4 m)

Supervised Input

2-Conductor 18-24 AWG

500 feet (152.4 m)

Wiegand/Proximity Readers

7-Conductor 18-22 AWG Shielded

500 feet (152.4 m)

NOTE: 

Main power supply and control wiring MUST be run in separate conduits. Conduits must be UL approved for low and high 

voltage. Refer to the NEC for additional wiring requirements.

Category 5e cabling is the minimum performance category recommended.

Wiring shall be in accordance with the National Electrical Code (ANSI/NFPA 70), local codes and authorities having jurisdiction.

Always provide power from a dedicated source. Plug provided transformer into an outlet wired to its own 10 Amp minimum circuit 

breaker. This will prevent two problems:
  •  Other equipment cannot introduce spikes, noise, surges or dips into the power circuit that will affect the system.
  •  The system’s operation will not be affected if any other equipment develops a short circuit across the power line.

* CAT 5/6 NETWORK CABLE NOTES:

  •   For outdoor distances exceeding 140 feet (42.7 m), a UL497 compliant primary surge protector MUST be installed at the CAPXM.
  •   Distances exceeding 328 feet (100 m) may be accommodated with additional hardware (available through third-party sources).

PRE-INSTALL

NETWORK

INSTALL

ACCESS CONTROL

INTRODUCTION

INTRODUCTION

PRE-INSTALL

NETWORK

INSTALL

ACCESS CONTROL

INTRODUCTION

PRE-INSTALL

NETWORK

INSTALL

ACCESS CONTROL

INTRODUCTION

PRE-INSTALL

NETWORK

INSTALL

ACCESS CONTROL

INTRODUCTION

PRE-INSTALL

NETWORK

INSTALL

ACCESS CONTROL

Summary of Contents for myQ Business CAPXM






















Reviews: