background image

3

Never expose eyes or skin to UVC light from any source. Looking directly at the UVC

light may cause permanent eye damage or blindness. Never operate the CX-Aire Air Purifying System
out of the plenum. Avoid touching the glass portion of the lamp with your hands.

WARNING

CX-AIRE IN-DUCT AIR PURIFIER

MODEL:  CX-Aire

The delivery set includes: 

Ballast assembly and power cord

Mounting base

UVC germicidal lamp

UVC light shield

Sheet metal mounting screws (6)

Mounting template 

Ductboard adapter plate

This product is not sold as a medical device and is not for the purpose of

diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention
of any disease or condition.

Note: 

For applications with multiple systems, one unit per system is recommended. 

For larger applications, multiple units are recommended. 

BEFORE INSTALLATION

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING

WITH THE INSTALLATION.

Disconnect and lock out power supply before performing any installation work.

Working on or near energized equipment could result in death or serious injury.

This device MUST be installed by a qualified agency in accordance with the manufacturer's installation
instructions. The definition of a qualified agency is any individual, firm, corporation or company that
either in person or through a representative is engaged in, and is responsible for, the installation and
operation of HVAC appliances, who is experienced in such work, familiar with all the precautions
required, and has complied with all the requirements of the authority having jurisdiction.

SIZING & SELECTING UNITS

SQUARE

FOOTAGE

CX-AIRE

(for ducts at least 16” wide)

VOLTS / HZ

WATTS

AMPS

Up to 2000

1

120 / 60

30

.5

4000

2

120 / 60

30

.5

NOTICE

WARNING

NOTICE

Summary of Contents for CX-AIRE













Reviews: