background image

10

Never expose eyes or skin to UVC light from any source. Looking directly at the UVC

light may cause permanent eye damage or blindness. Never operate the CX-Aire Air Purifying System
out of the plenum. Avoid touching the glass portion of the lamp with your hands.

WARNING

TROUBLESHOOTING

Only qualified personnel should work on electrical equipment. Working on or

near energized equipment could result in death or serious injury.

1. Check to make sure 120VAC power is available at the electrical outlet. 
2. Do not wire the unit into the appliance fan circuit. This will cause premature ballast or lamp

failure and void the warranty. For proper operation, the unit requires 120VAC at all times. 

3. Pull back metal washer on mounting base. If lamp comes on, the base needs tightening to

ensure that the safety switch is fully engaged. 

4. If lamp does not light up, rotate ballast slightly clockwise or counterclockwise. 
5. If lamp does not light up after rotating ballast, replace lamp. 
6. If unit still does not light up after replacing lamp, replace unit. 

RECOMMENDED MAINTENANCE

Unplug unit from the electrical outlet before commencing inspection and cleaning. 

NOTE:  

Wear oil-free cotton gloves prior to maintenance in case of accidental breakage of glass. 

1. The lamp should be inspected and cleaned at least every 6 months. Frequency depends upon

the environment such as the type of air filter, duration of use and replacement cycle. 

2. To maintain maximum output intensity, replace the CX-Aire-RL lamp every 2 years. The lamp

should operate continuously for maximum lamp life and light effectiveness.

REPLACEMENT PARTS

Replacement parts are available from the following sources:

         •        Your local HVAC wholesaler or contractor
         •        Continental Fan Manufacturing Inc., Buffalo, NY (1-800-779-4021)
         •        www.continentalfan.com

WARNING

WARNING

MODEL

DESCRIPTION

UPC CODE

CX-Aire-RL

16” UVC Lamp (1 Only) 

6 27249 12224 1

CX-Aire-TB

Ballast

6 27249 12225 8

Summary of Contents for CX-AIRE













Reviews: