background image

CX-AIRE-I&M-2012

Buffalo, New York  |  Mississauga, Ontario  |  Dayton, Ohio

www.continentalfan.com   |   1-800-779-4021

The health aspects associated with the use of these products and their ability to aid in disinfecting of environmental air have not been investigated by UL.

CONNECTION CERTIFICATE 

Company name

Installed by

Installation date

Signature 

LIMITED WARRANTY

Subject to the provisions of the clauses herein, Vendor agrees to correct any defect or defects in
workmanship or materials which may develop under proper and normal use, by repair or by
replacement of the defective part or equipment, at Vendor’s option, FOB factory. Unless otherwise
stated, the warranty period for the CX-Aire shall be ten (10) years from date of shipment. The
exceptions to this warrant period are:  

UVC Lamp - ninety (90) days

This warranty is provided to the original Buyer, and may not be transferred, sold or bartered.
Motors, drives, electrical controls and other components manufactured for Vendor by others
are not covered by these warranty provisions. All warranty claims must be processed through
point of purchase. All warranty repair work must be performed either at the factory or by a factory
certified service center. For additional information regarding warranties, see Vendor document:
Limited Warranty-1105.

CLEAN-UP OF BROKEN LAMPS

See warnings on page two of this manual. 

UVC lamps contain a small amount of mercury, like a typical fluorescent lamp. DO NOT touch any
of the mercury with your bare hands. 

1.  While wearing disposable, non-absorbent protective gloves, carefully pick up the large pieces

of glass with your hands. 

2.  Then, vacuum the entire area with a standard household vacuum cleaner ensuring the removal

of all lamp material. 

3.  Dispose of the pieces of glass, the vacuum cleaner bag, and the disposable gloves in a sealed

garbage bag. 

4.  Check with your local waste management authority for local disposal or recycling requirements. 
5.  Wash hands and remove and wash clothes for added safety measures.

NOTICE

Summary of Contents for CX-AIRE













Reviews: