Cely LVC-50 User Manual Download Page 16

Series VC-50 / SVC-50 / MVC-50 / LVC-50

49-MCVC50EN03

12

USER´S MANUAL

12. TECHNICAL 

CONFIGURATION

Press 

 when the scales are in normal weighing mode and the display will show “F0 H-L”. Press 

 until

the display shows “PROG” and press 

 to enter. The display will show “PIN”. Then press 

 

 and 

to enter Technical Configuration mode and 

 to select the parameter. Press 

 to save and 

 to exit.

FUNCTIÓN

SUB-FUNCTIÓN

DESCRIPTION

AZN 0

This option is used to select zero tracking options.
Options: 0,5d, 1d, 2d, 4d

0-AUTO

This option is used to select the initial zero setting range when
the indicator turns
Options: 0%, 2%, 5%, 10%, 20%

0- RANGE

This option is used to select the manual zero range when the
ZERO key is pressed
Options: 2%, 4%, 10%, 20%, 50%, 100%

P1 REF

Speed

This determines the ADC speed. Press 

 to select the ADC

speed and 

 to save it.

7.5: 7.5 times per second
15: 15 times per second
30: 30 times per second
60: 60 times per second
Note: 15 or 30 times per second is recommended

DECI

This option is used to select the decimal point.
Options: 0, 0.0, 0.00, 0.000, 0.0000

INC

This option is used to select the step.
Options: 1, 2, 5, 10, 20, 50

C AP

This display shows xxxxx to set-up capacity. After selecting,
the VC-50 / SVC-50 / MVC-50 / LVC-50 will show the
parameter for animal weighing scales if the external resolution
that has been set is below 1/3000.
First, set the vibration range. Use 

 to select the desired

value: 0(deactivated)/5/10/15/20/25/30/35/40/45/50, vibrations
in reading data in the range that you determine. The reading
will be set.
Then set-up the reading-block option. A1 (block minimum
data), A2 (block mean data), A3 (block maximum data)
Then set-up the increase value. Press  

  

 to enter data,

and then 

 to save. After setting up this data, when the

readings have been saved, if any items are added to the
platform or any products are removed, the reading will be
updated and saved again.
Then set-up the delay time: 50/60/70/80.
Then set-up the block conditions. 3 may be selected (the VC-
50 / SVC-50 / MVC-50 / LVC-50 will block reading data if it
detects reading data in a vibration range of 3 times) or 8 (it will
block if reading data is detected in a vibration range of 8
times).

P 2 CAL

CAL

Calibration, see details in section 10.

TRI

This display shows xxxxx to trimmer load cells.

COUNT

This display shows

 

xxxxx to indicate internal counting

.

P3 P RO

RESET

This resets the original factory default set-up.

Summary of Contents for LVC-50




















Reviews: