background image

4

Motor Identification Plate

RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! 

Please take a moment to locate the model number and serial number from your fan (see below) and record 
this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear 
there already� These numbers are found on the motor identification plate affixed to the fan motor in the 
location shown below:

PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to 
shipment� Before you begin to assemble and install your Casablanca fan, remove all 
parts from the carton and check them against the Parts Guide in this manual�
Make sure all parts are included in the box using the Parts Guide on the following pages�

If there are missing or broken parts: 
Call 1-888-227-2178 Monday through Friday, 8 a�m� 
to 4:30 p�m� CT� Your request will be handled 
immediately� Replacement parts will be sent to you 
via Federal Express�

Proper Parts Handling

Do not remove lightbulbs from their packaging 
until you are ready to install them� 

Before discarding packaging materials, be certain 
that all parts have been removed� 

Use a clean, dry paintbrush to remove small 
Styrofoam pieces that may remain after unpacking�

Do not brush Styrofoam into wiring cavities� 
The blades in each pack are matched for equal 
weight to assure smooth fan operation� If more 
than one fan is being installed, do not mix blades 
from different cartons� 

When cleaning, painting, or working near your fan, 
be cautious of the fan and blades�

Always turn power to the ceiling fan OFF before 
replacing lightbulbs or working on your fan� 

Never insert anything into the path of the fan 
blades while the fan is in operation� 

Never install a fan over a pool or spa� 

Never operate a fan that has been damaged in any 
way� 

Install the fan according to the instructions in this 
manual�

If the fan does not work:

Refer to the Troubleshooting Tips in this Owner’s 
Manual�

Call Technical Support at 1-888-227-2178�
Contact your local Authorized Service Center�
Our Web site at www�casablancafanco�com 
contains additional information on Casablanca 
products, troubleshooting, and Authorized Dealer 
or Service Centers� Please do not return this 
product to the store�

Serial Number

Veneto 
TYPE 

  HANGER TYPE

DJ01 1151      MODEL C32G611L

Memphis, TN

 SERIAL  No.: 

DJ06 2237

       

C32G611L

Model Number

Summary of Contents for Ceiling fans



























Reviews: