8
Table 5
─
Menu Structure
a
(cont)
Menu
Parameter
Parameter
Default
Value
Parameter
Range and Increment
b
Notes
SYSTEM
SETUP
FACTORY DEFAULT
NO
NO or YES
Resets all set points to factory defaults when set to YES. LCD will
briefly flash YES and change to NO but all parameters will change to
the factory default values.
ADVANCED
SETUP
MA LO SET
45
o
F
35 to 55
o
F;
Incremented by 1
o
Temperature to achieve Freeze Protection (close damper and alarm if
temperature falls below setup value).
FREEZE POS
CLO
CLO or MIN
Damper position when freeze protection is active (closed or MIN POS).
CO2 ZERO
0ppm
0 to 500 ppm;
Increment by 10
CO
2
ppm level to match CO
2
sensor start level.
CO2 SPAN
2000ppm
1000 to 3000 ppm;
Increment by 10
CO
2
ppm span to match CO
2
sensor.
STG3 DLY
2.0h
0 min, 5 min, 15 min,
then 15 min intervals.
Up to 4 h or OFF
Delay after stage 2 cool has been active. Turns on 2
nd
stage of cooling
when economizer is 1
st
stage and mechanical cooling is 2
nd
stage.
Allows three stages of cooling, 1 economizer and 2 mechanical.
OFF = no Stage 3 cooling
SD DMPR POS
CLO
CLO or OPN
Indicates shutdown signal from space thermostat or unitary controller.
When controller receives 24 Vac input on the SD terminal in conven-
tional mode, the OA damper will open if programmed for OPN and OA
damper will close if programmed for CLO. All other controls, e.g., fans,
etc. will shut off.
DCVCAL ENA
MAN
MAN (manual)
AUTO
Turns on the DCV automatic control of the dampers. Resets ventilation
based on the RA, OA, and MA sensor conditions. Requires all 3 RA,
OA, and MA sensors.
MAT T CAL
0.0
o
F
+/-2.5
o
F
Allows for the operator to adjust for an out of calibration temperature
sensor.
OA T CAL
0.0
o
F
+/-2.5
o
F
Allows for the operator to adjust for an out of calibration temperature
sensor.
OA H CAL
0% RH
+/-10% RH
Allows for operator to adjust for an out of calibration humidity sensor.
RA T CAL
0.0
o
F
+/-2.5
o
F
Allows for the operator to adjust for an out of calibration temperature
sensor.
RA H CAL
0% RH
+/-10% RH
Allows for operator to adjust for an out of calibration humidity sensor.
DA T CA;
0.0
o
F
+/-2.5
o
F
Allows for the operator to adjust for an out of calibration temperature
sensor.
CHECKOUT
DAMPER VMIN─HS
n/a
n/a
Positions damper to VMIN position
DAMPER VMAX─HS
n/a
n/a
Positions damper to VMAX position
DAMPER OPEN
n/a
n/a
Position damper to the full open position.
Exhaust fan contacts enable during the DAMPER OPEN test. Make
sure you pause in the mode to allow exhaust contacts to energize due
to the delay in the system.
DAMPER CLOSE
n/a
n/a
Positions damper to the fully closed position
CONNECT Y1─O
n/a
n/a
Closes the Y1─O relay (Y1─O)
CONNECT Y2─O
n/a
n/a
Closes the Y2─O relay (Y2─O)
CONNECT AUX
n/a
n/a
Energizes the AUX output. If Aux setting is:
• NONE ─ not action taken
• ERV ─ 24 Vac out. Turns on or signals an ERV that the conditions
are not good for economizing but are for ERV operation.
d
• SYS ─ 24 Vac out. Issues a system alarm
ALARMS(
_
)
MA T SENS ERR
n/a
n/a
Alarms display only when they are active. The menu title “ALARMS(_)”
includes the number of active alarms in parenthesis ( ).
CO2 SENS ERR
n/a
n/a
OA T SENS ERR
n/a
n/a
DA ENTHL ERR
n/a
n/a
SYS ALARM
n/a
n/a
When AUX is set to SYS and there is any alarm (e.g., failed sensors,
etc.), the AUX terminal has 24 Vac out.
NOTE:
The alarms listed are examples. Additional alarms display depending on the parameter settings and configuration.
For example if you do not have a DCV (CO
2
) sensor, then none of the DCV parameters appear.
a
Table 2 illustrates the complete hierarchy. Your menu parameters may be different depending on your configuration.
For example if you do not have a DCV (CO
2
) sensor, then none of the DCV parameters appear
b
When values are displayed, pressing and holding the ▲ or ▼ button causes the display to automatically increment.
c
n/a = not applicable
d
ERV Operation: When in Cooling mode AND the conditions are NOT OK for economizing - the ERV terminal will be energized.
In the Heating mode the ERV terminal will be energized when the OA is below the ERV OAT setpoint in the setpoint menu.
