background image

7

Table 5 

 Menu Structure

a

 (cont)

Menu

Parameter

Parameter

Default

Value

Parameter

Range and Increment

b

Notes

SETPOINTS

MAT SET

53

o

F

38 to 65

o

F;

increment by 1

Setpoint determines where the economizer will modulate the OA 

damper to maintain the mixed air temperature.

LOW T LOCK

32

o

F

-45 to 80

o

F;

increment by 1

Setpoint determines outdoor temperature when the mechanical cooling 

cannot be turned on. Commonly referred to as the Compressor lockout.

DRYBLB SET

63

o

F

48 to 80

o

F;

increment by 1

Setpoint determines where the economizer will assume outdoor air 

temperature is good for free cooling; e.g.; at 63

o

F unit will economize at 

62

o

F and below and not economize at 64

o

F and above. There is a 2

o

deadband.

ENTH CURVE

ES3

ES1,ES2,ES3,ES4, or

ES5

Enthalpy boundary “curves” for economizing using single enthalpy

DCV SET

1100ppm

500 to 2000ppm;

increment by 100

Displays only if CO

2

 sensor is connected. Setpoint for Demand Control 

Ventilation of space. Above the setpoint, the OA dampers will modulate 

open to bring in additional OA to maintain a space ppm level below the 

setpoint.

MIN POS

4.4 V

2 to 10 Vdc

Displays ONLY if a CO

2

 sensor is NOT connected

VENTMAX  With 2-speed 

fan units VENTMAX L (low 

speed fan) and VENTMAX 

H (high speed fan) settings 

are required

4.4 V

2 to 10 Vdc

or

100 to 9990 cfm

increment by 10

Displays only if a CO

2

 sensor is connected. Used for Vbz (ventilation 

max cfm) setpoint. Displays 2 to 10 V if <3 sensors (RA,OA, and MA). 

In AUTO mode dampers controlled by CFM

VENTMAX L

6 V

VENTMAX H

4.4 V

VENTMIN  With 2-speed 

fan units VENTMIN L (low 

speed fan) and VENTMIN 

H (high speed fan) set

2.8 V

2 to 10 Vdc

or 100 to 9990 cfm

increment by 10

Displays only if a CO

2

 sensor is connected. Used for Ba (ventilation min 

cfm) setpoint. Displays 2 to 10 V if <3 sensors (RA, OA, and MA). Va 

is only set if DCV is used. This is the ventilation for less than maximum 

occupancy of the space. In AUTO mode dampers controlled by CFM.

VENTMIN L

3.7 V

VENTMIN H

2.8 V

ERV OAT SP

32

o

F

0 to 50

o

F;

increment by 1

Only when AUX1 O = ERV

EXH1 SET  With 2-speed 

fan units Exh1 L (low speed 

fan) and Exh1 H (high 

speed fan) settings are 

required

50%

0 to 100%;

increment by 1

Setpoint for OA damper position when exhaust fan 1 is powered by the 

economizer.

Exh1 L

65%

Exh1 H

50%

EXH2 SET  With 2-speed 

fan units Exh2 L (low speed 

fan) and Exh2 H (high 

speed fan) settings are 

required

75%

0 to 100%;

increment by 1

Setpoint for OA damper position when exhaust fan 2 is powered by the 

economizer. Only used when AUX is set to EHX2.

Exh2 L

80%

Exh2 H

75%

SYSTEM

SETUP

INSTALL

01/01/10

Display order = MM/DD/YY

Setting order = DD, MM, then YY.

UNITS DEG

o

F

o

F or 

o

C

Sets economizer controller in degrees Fahrenheit or Celsius

EQUIPMENT

CONV

Conventional or HP

CONV = conventional; HP O/B = Enable Heat Pump mode. Use AUX2 I 

for Heat Pump input from thermostat or controller.

AUX2 I

W

SD/W or HP(O)/HP(B)

In CONV mode: SD + Enables configuration of shutdown (default); W 

= Informs controller that system is in heating mode. In HP O/B mode: 

HP(O) = energize heat pump on Cool (default); HP(B) = energize heat 

pump on heat.

FAN TYPE

2 speed

1 speed/2 speed

Sets the economizer controller for operation of 1 speed or 2 speed 

supply fan.

FAN CFM

5000cfm

100 to 15000 cfm;

increment by 100

This is the capacity of the RTU. The value is found in the Project 

Submittal documents for the specific RTU.

AUX OUT

NONE

NONE

ERV

EXH2

SYS

•  NONE = not configured (output is not used)

•  ERV = Energy Recovery Ventilatio

n

•  EXH2 = second damper position relay closure for second exhaust fan

•  SYS = use output as an alarm signal

OCC

INPUT

INPUT or ALWAYS

When using a setback thermostat with occupancy out (24 Vac), the 24 

Vac is input “INPUT” to the OCC terminal. If no occupancy output from 

the thermostat then change program to “ALWAYS” OR add a jumper 

from terminal R to OCC terminal

Summary of Contents for CRECOMZR067A00















Reviews: