background image

1

Installation Instructions

Read these instructions completely before attempting to install the 

Vertical EconoMi$er X Accessory.

CONTENTS

SAFETY CONSIDERATIONS . . . . . . . . . . . . . .1

GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

EconoMi$er X Sensor Usage . . . . . . . . . . . . . 2

ACCESSORIES LIST. . . . . . . . . . . . . . . . . . . . .2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 2-5

EconoMi$er X Standard Sensors . . . . . . . . . .5

EconoMi$er X Control Modes . . . . . . . . . .

 

5-11 

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 

 

13

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance, or 

use can cause explosion, fire, electrical shock or other conditions which 

may  cause  personal  injury  or  property  damage.    Consult  a  qualified 

installer, service agency, or your distributor or branch for information or 

assistance.  The qualified installer or agency must use factory-authorized 

kits or accessories when modifying this product.  Refer to the individual 

instructions packaged with the kits or accessories when installing.
Follow  all  safety  codes.    Wear  safety  glasses  and  work  gloves.    Use 

quenching  cloths  for  brazing  operations  and  have  a  fire  extinguisher 

available.  Read these instructions thoroughly and follow all warnings 

or cautions attached to the unit.  Consult local building codes and 

appropriate national electrical codes (in USE, ANSI/NFPA70, National 

Electrical Code (NEC); in Canada, CSA C22.1) for special requirements.

It is important to recognize safety information.  This is the safety-alert 

symbol      .  When you see this symbol on the unit and in instructions or 

manuals, be alert to the potential for personal injury.

Understand  the  signal  words  DANGER, WARNING,  CAUTION,  and 

NOTE.  These words are used with the safety-alert symbol.

DANGER identifies the most serious hazards which 

will

 result in severe 

personal  injury  or  death.    WARNING  signifies  hazards  which 

could

 

result in personal injury or death.

CAUTION  is  used  to  identify  unsafe  practices,  which 

may

 result in 

minor  personal injury or product and property damage.

NOTE  is  used  to  highlight  suggestions  which 

will

 result in enhanced 

installation, reliability, or operation.

GENERAL

The  EconoMi$er  X  system  utilizes  the  latest  technology  available 

for  integrating  the  use  of  free  cooling  with  mechanical  cooling  for 

packaged rooftop units. The solid-state control system optimizes energy 

consumption,  zone  comfort,  and  equipment  cycling  by  operating  the 

compressors when the outdoor-air temperature is too warm, integrating 

the  compressor  with  outdoor  air  when  free  cooling  is  available,  and 

locking  out  the  compressor  when  outdoor-air  temperature  is  too  cold. 

Demand control ventilation is supported. 
Units displaying 17th position of the model number to indicate that the 

unit  is  equipped  with  the  factory-installed  VFD  (Variable  Frequency 

Drive) option for 2-speed indoor fan control.  The VFD option is required 

for units equipped with EconoMi$er X.  For detailed information on the 

VFD  see  the Variable  Frequency  Drive  (VFD)  Installation,  Setup  and 

Troubleshooting Supplement.
The EconoMi$er X system utilizes gear-drive technology with a direct-

mount  spring  return  actuator  that  will  close  upon  loss  of  power.  The 

EconoMi$er X system comes standard with an outdoor air temperature 

sensor, mixed air temperature sensor. Outdoor enthalpy, indoor enthalpy, 

and  CO2  sensors  are  available  for  field  installation.  See  Table  3  for 

sensor usage.

IMPORTANT

: The economizer outside air dampers meet the ASHRAE 

90.1  leakage  requirements.    Economizer  must  be  installed  perfectly 

square to avoid damper leakage. Squareness tol/- 1/32”.
Standard barometric relief dampers provide natural building pressurization 

control. An optional power exhaust system is available for applications 

requiring even greater exhaust capabilities. The power exhaust set point 

is adjustable at the EconoMi$er X controller.

See Table 1 for package usage. See Table 2 for package contents. See 

Table 3 for sensor usage.

ACCESSORIES LIST

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could cause personal injury or death. 

Before performing service or maintenance operations on the unit, 

always  turn  off  main  power  switch  to  unit  and  install  lock(s)  and 

lockout tag(s). Unit may have more than one power switch. Ensure 

electrical  service  to  rooftop  unit  agrees  with  voltage  an  amperage 

listed on the unit rating plate.

CAUTION

CUT HAZARD

Failure to follow this caution may result in personal injury. 

Sheet metal parts may have sharp edges or burrs. Use care and wear 

appropriate  protective  clothing,  safety  glasses  and  gloves  when 

handling parts and servicing roof top units.

!

!

Table 1 - Package Usage

Table 2 - Package Contents

UNIT SIZE

PART NUMBER

Small Cabinet,

Footprint size: 46 3/4” x 74 3/8”

CRECOMZR067A02

Large Cabinet,

Footprint size: 58 1/2” x 88 1/8”

CRECOMZR069A03

Extra-Large Cabinet,

Footprint size: 63 3/8” x 115 7/8”

CRECOMZR071A00

PACKAGE NO.

QTY

CONTENTS

CRECOMZR067A00,

CRECOMZR069A00

1

1

1

18

1

1

Hood Top and Sides

Hood Divider

Aluminum Filter

Screws

EconoMi$er X Assembly

Mixed Air Temperature Sensor

CRECOMZR071A00

1

1

1

2

1

1

1

Hood Top and Sides

Hood Divider

Hood Filter Divider

Aluminum Filters

Hardware Bag

EconoMi$er X Assembly

Mixed Air Temp Sensor

Small Rooftop Products

3 to 12 ½ Tons

Vertical EconoMi$er X Accessory

CRECOMZR067A00 

CRECOMZR069A00

CRECOMZR071A00

!

Summary of Contents for CRECOMZR067A00















Reviews: