4–29
T-359
Cd50
CCPC Disabled
Code 50 allows selection of CCPC mode. The user can press ENTER, then arrow
keys, then ENTER again to enable (On) or suspend (OFF) CCPC mode. If CCPC op-
eration is On, it may be suspended due to one of the following conditions:
“SEtPt” =Set point is too low.
“CAHUM”= CA or humidity control is active
“ACT”=ACT is active.
“FAIL”=Return temperature probe has failed.
“PrtrP”=Pre-trip is active.
“C LIM”= Cool limit logic is active.
“PULL”=Unit is in pulldown mode.
Cd51
Automatic Cold
Treatment
Parameter
Selection
Code Cd51 initially displays countdown timer increments of 1 day, 1 hour with the
temperature default. Pressing ENTER allows selection of within the current menu and
proceeds to the next menu. After five seconds of no activity, the display reverts to nor-
mal system display, but retains the parameters previously selected.
“ACt” = “On,” “Off” or “----”. The default is Off.
“trEAt”=C /F in 0.1 degree increments. The default is 0.0
C.
“DAyS”= “0-99” increments of 1. The default is 0.
“ProbE”=probe positions (example 12°4). The default is ----.
“SPnEW”= C /F in 0.1 degree increments. The default is 10.0
C.
Cd53
Automatic Set
point Change
Mode
Parameter
Selection
Code Cd53 initially displays countdown timer increments of 1 day, 1 hour with the
temperature default. Pressing ENTER allows selection of within the current menu and
proceeds to the next menu. After five seconds of no activity, the display reverts to nor-
mal system display, but retains the parameters previously selected.
“ASC”=”On” or “Off” The default is Off.
“NSC”=”1-2”
“SP 0"=C /F in 0.1 degree increments. The default is 10.0
C.
“DAY 0"= “0-99” increments of 1. The default is 1.
“SP 1"=C /F in 0.1 degree increments. The default is 10.0
C.
“DAY 1"= “0-99” increments of 1. The default is 1.
“SP 2"=C /F in 0.1 degree increments. The default is 10.0
C.
Cd54
Electronic
Expansion Valve
Status
Reading for evaporator superheat is shown on the right display. Press ENTER at
Cd54 to show reading for EEV position (in%) on left display.
Cd55
Discharge
Super Heat
Code Cd55 will display the discharge superheat values in C /F as calculated by the
discharge temperature minus the discharge saturation temperature as calculated
from discharge pressure. “-----” will be displayed if selection is not valid.
Cd58
Water Pressure
Switch/Condenser
Fan Switch State
or Override Logic
State
Code Cd58 will display “CLOSE” if the WPS or CFS switch contacts are closed or that
these options are not installed. “OPEn” is displayed when the WPS or CFS switch
contacts are open. When the WPS/CFS Override Logic is “TRUE”, the right display
will flash on all units.
Cd59
Pump Down Logic
Code Cd59 allows operation of the pump down logic control. The display will flash be-
tween “STArT PdN” and “PrESS EnTEr”. Once the operator confirms continuation of
the sequence, pump down logic begins. If pump down logic is completed within 20
minutes, the unit will turn off and the display will flash “P dN DOnE” and “SHUT OFF”.
The operator must shut off the unit. If the pump down logic is not completed within 20
minutes, the unit will return to its previous control condition.
Table 4–5 Controller Function Codes (Continued)
CODE #
TITLE
DESCRIPTION
Summary of Contents for 69NT40-561-019
