SP8018
TRX
MACHINE CONTROLS
11
ENGINE CONTROLS – Refer to the engine manufacturers owners’ manual for controls,
operation, and service.
•
THE CUTTER WHEEL MUST BE
DISENGAGED BEFORE STARTING
THE MACHINE.
•
The SP8018
TRX
stump grinder is a radio
control machine. To start the engine and
radio control transmitter, follow these
instructions.
•
On the machine, turn the ignition key
switch to ON, the machine switch to
Remote On,
and make sure the flow and
gear switches are in the LOW position.
•
On the transmitter, press the
E-STOP
button down.
•
Toggle any switch on the transmitter.
•
Twist the
E-STOP
button clockwise to
release. Release the E-STOP button
within 10 seconds to power up or the unit
will power down. When the transmitter is
operating there is a yellow light that will
be flashing, the light is indicated in the
picture at the right. (Read the radio
control manual for more information on
the meaning of different lights and colors.)
If the transmitter doesn’t start, check the
transmitter for stuck switches; it will not
start with a switch in the ON position.
•
Now start the engine, turn the key switch
while pressing the by-pass switch to start
the machine. If the engine doesn’t start
right away and you have to restart it, turn
the key switch OFF and back ON. Make
sure the light on the transmitter is still on,
and restart the engine by turning the key
and pressing the by-pass switch. If you
lose the connection (light off), repeat the
procedure from the beginning and perform
each step exactly as described. Test
controls for proper operation.
TOGGLE ANY
SWITCH
E-STOP BUTTON
A YELLOW LIGHT
WILL BE FLASHING
WHEN RADIO IS
SENDING SIGNALS
TO THE RECEIVER
BATTERY LOW /
FAULT LIGHT
PUSH SWITCH UP
TO REMOTE ON
FLOW AND GEAR
SWITCHES MUST
BE IN LOW
KEY
SWITCH
BY-PASS
SWITCH
NEVER WELD ON A MACHINE WITH
RADIO CONTROLS WITHOUT FIRST
DISCONNECTING THE RECEIVER WIRE
HARNESS, OTHERWISE THE RADIO
RECEIVER WILL BE DESTROYED.
DO NOT OPERATE THE ENGINE AT
AN ANGLE GREATER THAN 25° OR
SEVERE ENGINE DAMAGE WILL
OCCUR.
PROPER ENGINE OIL LEVEL
MUST BE MAINTAINED TO ACHIEVE
MAXIMUM ANGLE OF OPERATION OF
25°. (See Engine Owner’s Manual for
proper oil level.)
Summary of Contents for SP8018 TRX
