manualshive.com logo in svg

Canon Puncher Unit-L1, Installation Procedure

Share
Download
Canon Puncher Unit-L1 Installation Procedure Download Page 7

Contents

Contents

第

1

章　

Installation Procedure

1.1 Making Pre-Checks ............................................................................................................................................... 2

1.1.1Checking the Contents..................................................................................................................................... 2
1.1.2Installing the Accessories................................................................................................................................ 4

1.2 Unpacking and Checking the Components ........................................................................................................... 8

1.2.1Unpacking ....................................................................................................................................................... 8

1.3 Installation Procedure............................................................................................................................................ 9

1.3.1Disconnecting the Finisher from its Host Machine......................................................................................... 9
1.3.2Connecting to the Finisher ............................................................................................................................ 12
1.3.3Preparing the Host Machine for Installation ................................................................................................. 15
1.3.4Connecting to the Host Machine ................................................................................................................... 18
1.3.5Checking the Height/Tilt ............................................................................................................................... 19

1.4 Making Adjustments ........................................................................................................................................... 22

1.4.1Adjusting the Height/Tilt............................................................................................................................... 22
1.4.2Work After Making Checks/Adjustments..................................................................................................... 25

1.5 Attaching the Labels etc. ..................................................................................................................................... 29

1.5.1Attaching the Label ....................................................................................................................................... 29

Summary of Contents for Puncher Unit-L1









































Reviews:

No comments

Brands by name

Popular brands

Load more brands